Full-Length Grooved Pins with Pilot manufactured in A4 Stainless Steel (ISO 3506 group A4 (316 / 1.4401), commonly supplied A4-80) are dimensioned to ISO 8739. The sections below give the mechanical and physical properties of the grade, its behavior in corrosive and elevated-temperature service, and the full size table.
Why Choose A4 Stainless Steel for Full-Length Grooved Pins with Pilot
Specified for marine, coastal and chemical applications. For full-length grooved pins with pilot, this matters when superior, including marine and chloride environments is the primary requirement.
Mechanical & Physical Properties
| Grade designation | ISO 3506 group A4 (316 / 1.4401), commonly supplied A4-80 |
|---|---|
| Magnetic response | Largely non-magnetic |
| Service temperature | approx. -200 °C to +400 °C, subject to the property class and the joint |
| Corrosion characteristic | Superior, including marine and chloride environments |
Corrosion Behavior in Service
A4 (316) adds 2–3% molybdenum to the A2 (304) composition, which dramatically improves resistance to chloride-pitting corrosion. For Full-Length Grooved Pins with Pilot in marine, coastal, swimming-pool or food-processing environments, A4 is the default selection.
Comparable Grades
For Full-Length Grooved Pins with Pilot, the alternative stainless grade is A2 (304). A2 (304) covers general indoor and outdoor service. A4 (316) adds molybdenum, which is what buys the chloride resistance for marine and de-icing-salt exposure. Where strength matters more than corrosion, plated alloy steel in class 8.8 or 10.9 is the swap to make.
Using Stainless Fasteners in Aluminum
Stainless steel is more noble than aluminum, so with an electrolyte present — rain, condensation, salt spray — the aluminum becomes the anode and corrodes at the joint. Area ratio decides how bad it gets: a small stainless fastener in a large aluminum section is normally acceptable, a large stainless fastener in thin aluminum is not. Where the joint gets wet, isolate the metals with a coated or nylon washer and a sealant, or specify an aluminum or coated fastener instead.
Sizes of Full-Length Grooved Pins with Pilot Available in A4 Stainless Steel
| Nominal diameter d (mm) | d_1 (mm) | d_2 (mm) | c (mm) | a (mm) | Length range l (mm) | Reference standard |
|---|---|---|---|---|---|---|
| 1.5 mm | 1.5 | 1.6 | 1.5 | 0.2 | 8~20 | ISO 8739 |
| 2 mm | 2 | 2.15 | 1.5 | 0.25 | 8~30 | ISO 8739 |
| 2.5 mm | 2.5 | 2.65 | 2 | 0.3 | 10~30 | ISO 8739 |
| 3 mm | 3 | 3.2 | 2 | 0.4 | 10~40 | ISO 8739 |
| 4 mm | 4 | 4.25 | 2.5 | 0.5 | 10~60 | ISO 8739 |
| 5 mm | 5 | 5.25 | 2.5 | 0.63 | 14~60 | ISO 8739 |
| 6 mm | 6 | 6.3 | 3.5 | 0.8 | 14~80 | ISO 8739 |
| 8 mm | 8 | 8.3 | 3.5 | 1 | 14~100 | ISO 8739 |
| 10 mm | 10 | 10.35 | 4.5 | 1.2 | 14~100 | ISO 8739 |
| 12 mm | 12 | 12.35 | 4.5 | 1.6 | 18~100 | ISO 8739 |
| 16 mm | 16 | 16.4 | 4.5 | 2 | 22~100 | ISO 8739 |
| 20 mm | 20 | 20.5 | 6.5 | 2.5 | 26~100 | ISO 8739 |
| 25 mm | 25 | 25.5 | 6.5 | 3 | 26~100 | ISO 8739 |
Dimensions are independent of the material: every size above is available in A4 Stainless Steel.
Custom manufacturing · Made to drawing
Need this pin in a grade that is not listed?
A4 Stainless Steel is one of the grades the catalog describes. Tolerance class is what a special pin usually turns on — a locating pin and a retaining pin want very different fits in the same nominal size. Made by cold heading or turning.
Minimum order from 2,000 pieces; samples within 7 days of drawing approval.
