Nyloc Lock Nuts manufactured in A4 Stainless Steel (ISO 3506 group A4 (316 / 1.4401), commonly supplied A4-80) are dimensioned to DIN 985 / ISO 7040. The sections below give the mechanical and physical properties of the grade, its behavior in corrosive and elevated-temperature service, and the full size table.
Why Choose A4 Stainless Steel for Nyloc Lock Nuts
Specified for marine, coastal and chemical applications. For nyloc lock nuts, this matters when superior, including marine and chloride environments is the primary requirement.
Mechanical & Physical Properties
| Grade designation | ISO 3506 group A4 (316 / 1.4401), commonly supplied A4-80 |
|---|---|
| Magnetic response | Largely non-magnetic |
| Service temperature | approx. -200 °C to +400 °C, subject to the property class and the joint |
| Corrosion characteristic | Superior, including marine and chloride environments |
Corrosion Behavior in Service
A4 (316) adds 2–3% molybdenum to the A2 (304) composition, which dramatically improves resistance to chloride-pitting corrosion. For Nyloc Lock Nuts in marine, coastal, swimming-pool or food-processing environments, A4 is the default selection.
Comparable Grades
For Nyloc Lock Nuts, the alternative stainless grade is A2 (304). The practical dividing line is chlorides: A2 (304) is fine until salt is involved, and A4 (316) exists for the cases where it is — coastal, marine and road-salt service. Neither reaches the strength of a plated class 8.8 or 10.9 fastener.
Using Stainless Fasteners in Aluminum
The galvanic couple here runs the wrong way: aluminum is the less noble metal, so it corrodes and the fastener does not. What governs the rate is the ratio of areas — a large anode and a small cathode is a tolerable combination, the reverse concentrates the attack into thin material around the hole. An isolating washer plus sealant breaks the circuit; where that is impractical, match the fastener to the substrate.
Sizes of Nyloc Lock Nuts Available in A4 Stainless Steel
| Size | Pitch (mm) | Width across flats s (mm) | Width across corners e min (mm) | Total height m (mm) | Metal height (mm) | Reference standard | Notes |
|---|---|---|---|---|---|---|---|
| M3 | 0.5 | 5.5 | 6.01 | 4.0 | 2.4 | DIN 985 / ISO 7040 | With nylon insert, single use |
| M4 | 0.7 | 7.0 | 7.66 | 5.0 | 3.2 | DIN 985 / ISO 7040 | With nylon insert, single use |
| M5 | 0.8 | 8.0 | 8.79 | 5.0 | 3.7 | DIN 985 / ISO 7040 | With nylon insert, single use |
| M6 | 1.0 | 10.0 | 11.05 | 6.0 | 4.7 | DIN 985 / ISO 7040 | With nylon insert, single use |
| M8 | 1.25 | 13.0 | 14.38 | 8.0 | 6.14 | DIN 985 / ISO 7040 | With nylon insert, single use |
| M10 | 1.5 | 16.0 | 17.77 | 10.0 | 8.04 | DIN 985 / ISO 7040 | With nylon insert, single use |
| M12 | 1.75 | 18.0 | 20.03 | 12.0 | 9.64 | DIN 985 / ISO 7040 | With nylon insert, single use |
| M14 | 2.0 | 21.0 | 23.36 | 14.0 | 11.0 | DIN 985 / ISO 7040 | With nylon insert, single use |
| M16 | 2.0 | 24.0 | 26.75 | 16.0 | 13.0 | DIN 985 / ISO 7040 | With nylon insert, single use |
| M20 | 2.5 | 30.0 | 32.95 | 20.0 | 16.0 | DIN 985 / ISO 7040 | With nylon insert, single use |
| M24 | 3.0 | 36.0 | 39.55 | 22.0 | 19.0 | DIN 985 / ISO 7040 | With nylon insert, single use |
| M30 | 3.5 | 46.0 | 50.85 | 25.0 | 24.0 | DIN 985 / ISO 7040 | With nylon insert, single use |
| M36 | 4.0 | 55.0 | 60.79 | 29.0 | 29.0 | DIN 985 / ISO 7040 | With nylon insert, single use |
Dimensions are independent of the material: every size above is available in A4 Stainless Steel.
Custom manufacturing · Made to drawing
Need this nut in a grade that is not listed?
A4 Stainless Steel is one of the grades the catalog describes. Thread, height, across-flats, property class, locking feature and flange form can all be varied, including thread sizes the standard series does not run to. Made by cold heading or tapping.
Minimum order from 2,000 pieces; samples within 7 days of drawing approval.
