A4 Stainless Steel (ISO 3506 group A4 (316 / 1.4401), commonly supplied A4-80) is specified for marine, coastal and chemical applications. Specified on slotted shims (horseshoe) it determines the corrosion behaviour (superior, including marine and chloride environments) and the service temperature range (approx. -200 °C to +400 °C, subject to the property class and the joint); the dimensions are ours rather than a standard's, and are listed in full below.
Why Choose A4 Stainless Steel for Slotted Shims (Horseshoe)
Specified for marine, coastal and chemical applications. For slotted shims (horseshoe), this matters when superior, including marine and chloride environments is the primary requirement.
Mechanical & Physical Properties
| Grade designation | ISO 3506 group A4 (316 / 1.4401), commonly supplied A4-80 |
|---|---|
| Magnetic response | Largely non-magnetic |
| Service temperature | approx. -200 °C to +400 °C, subject to the property class and the joint |
| Corrosion characteristic | Superior, including marine and chloride environments |
Corrosion Behavior in Service
A4 (316) adds 2–3% molybdenum to the A2 (304) composition, which dramatically improves resistance to chloride-pitting corrosion. For Slotted Shims (Horseshoe) in marine, coastal, swimming-pool or food-processing environments, A4 is the default selection.
Galvanic & Galling Considerations
For stainless slotted shims (horseshoe) the compatibility question is galvanic rather than galling: joined to aluminum or galvanized steel in wet service, stainless drives corrosion of the less-noble metal. Isolate with a coating, sleeve or non-conductive washer where the joint sees moisture. Note also that stainless is softer than hardened carbon steel, so where the part carries a wear or shear duty, check the load against the grade before substituting.
Using Stainless Fasteners in Aluminum
Expect the aluminum to corrode, not the fastener — stainless sits higher in the galvanic series, so the aluminum is the one that gives up material. A small fastener in a thick section spreads the loss over a large area and is usually fine; a large fastener in thin sheet concentrates it and is not. Keep water out of the joint, or isolate the two metals with a nylon or coated washer and a sealant.
Sizes of Slotted Shims (Horseshoe) Available in A4 Stainless Steel
| Slot width (mm) | Width A (mm) | Length (mm) | Thickness t (mm) | Material | Colour code | Typical use |
|---|---|---|---|---|---|---|
| 9 | 38 | 38 | 0.05 | Stainless 304 | None (bright) | Motor foot alignment |
| 9 | 38 | 38 | 0.10 | Stainless 304 | None (bright) | Motor foot alignment |
| 13 | 50 | 50 | 0.25 | Stainless 304 | None (bright) | Pump / gearbox feet |
| 13 | 50 | 50 | 0.50 | Stainless 304 | None (bright) | Pump / gearbox feet |
| 17 | 63 | 63 | 0.75 | Stainless 304 | None (bright) | Heavy machine bases |
| 17 | 63 | 63 | 1.00 | Stainless 304 | None (bright) | Heavy machine bases |
Dimensions are independent of the material: every size above is available in A4 Stainless Steel.
Custom manufacturing · Made to drawing
Need this standoff & spacer in a grade that is not listed?
A4 Stainless Steel is one of the grades the catalog describes. A non-standard standoff & spacer is quoted from the drawing; where one already exists in the catalog, the special is usually a variation on its tooling. Made by tapping or turning.
Minimum order from 2,000 pieces; samples within 7 days of drawing approval.







