A4 Stainless Steel (ISO 3506 group A4 (316 / 1.4401), commonly supplied A4-80) is specified for marine, coastal and chemical applications. Specified on snap-in pcb standoffs it determines the corrosion behaviour (superior, including marine and chloride environments) and the service temperature range (approx. -200 °C to +400 °C, subject to the property class and the joint); the dimensions are ours rather than a standard's, and are listed in full below.
Why Choose A4 Stainless Steel for Snap-In PCB Standoffs
Specified for marine, coastal and chemical applications. For snap-in pcb standoffs, this matters when superior, including marine and chloride environments is the primary requirement.
Mechanical & Physical Properties
| Grade designation | ISO 3506 group A4 (316 / 1.4401), commonly supplied A4-80 |
|---|---|
| Magnetic response | Largely non-magnetic |
| Service temperature | approx. -200 °C to +400 °C, subject to the property class and the joint |
| Corrosion characteristic | Superior, including marine and chloride environments |
Corrosion Behavior in Service
A4 (316) adds 2–3% molybdenum to the A2 (304) composition, which dramatically improves resistance to chloride-pitting corrosion. For Snap-In PCB Standoffs in marine, coastal, swimming-pool or food-processing environments, A4 is the default selection.
Galvanic & Galling Considerations
For stainless snap-in pcb standoffs the compatibility question is galvanic rather than galling: joined to aluminum or galvanized steel in wet service, stainless drives corrosion of the less-noble metal. Isolate with a coating, sleeve or non-conductive washer where the joint sees moisture. Note also that stainless is softer than hardened carbon steel, so where the part carries a wear or shear duty, check the load against the grade before substituting.
Using Stainless Fasteners in Aluminum
Stainless steel is more noble than aluminum, so with an electrolyte present — rain, condensation, salt spray — the aluminum becomes the anode and corrodes at the joint. Area ratio decides how bad it gets: a small stainless fastener in a large aluminum section is normally acceptable, a large stainless fastener in thin aluminum is not. Where the joint gets wet, isolate the metals with a coated or nylon washer and a sealant, or specify an aluminum or coated fastener instead.
Sizes of Snap-In PCB Standoffs Available in A4 Stainless Steel
| Spacing height (mm) | Body diameter (mm) | Fits board hole (mm) | Fits chassis hole (mm) | Board thickness (mm) | Flammability | Colour |
|---|---|---|---|---|---|---|
| 4.8 | 6.0 | 4.0 | 4.0 | 1.6 | UL94 V-2 | Natural |
| 6.4 | 6.0 | 4.0 | 4.0 | 1.6 | UL94 V-2 | Natural |
| 9.5 | 6.0 | 4.0 | 4.0 | 1.6 | UL94 V-2 | Natural |
| 12.7 | 6.0 | 4.0 | 4.0 | 1.6 | UL94 V-0 | Black |
| 15.9 | 6.0 | 4.0 | 4.0 | 1.6 | UL94 V-0 | Black |
| 19.1 | 6.0 | 4.0 | 4.0 | 2.0 | UL94 V-0 | Black |
Dimensions are independent of the material: the table above lists the sizes supplied, and on this page every one of them is quoted in A4 Stainless Steel. The catalogue's default material column has been omitted here so it cannot be read as contradicting that.
Custom manufacturing · Made to drawing
Need this standoff & spacer in a grade that is not listed?
A4 Stainless Steel is one of the grades the catalog describes. A non-standard standoff & spacer is quoted from the drawing; where one already exists in the catalog, the special is usually a variation on its tooling. Made by tapping or turning.
Minimum order from 2,000 pieces; samples within 7 days of drawing approval.








