Material specification page for t-slot nuts (din 508) in A4 Stainless Steel. Covers the grade designation (ISO 3506 group A4 (316 / 1.4401), commonly supplied A4-80), corrosion and magnetic behavior, comparable grades and their trade-offs, and the sizes available to DIN 508.
Why Choose A4 Stainless Steel for T-Slot Nuts (DIN 508)
Specified for marine, coastal and chemical applications. For t-slot nuts (din 508), this matters when superior, including marine and chloride environments is the primary requirement.
Mechanical & Physical Properties
| Grade designation | ISO 3506 group A4 (316 / 1.4401), commonly supplied A4-80 |
|---|---|
| Magnetic response | Largely non-magnetic |
| Service temperature | approx. -200 °C to +400 °C, subject to the property class and the joint |
| Corrosion characteristic | Superior, including marine and chloride environments |
Corrosion Behavior in Service
A4 (316) adds 2–3% molybdenum to the A2 (304) composition, which dramatically improves resistance to chloride-pitting corrosion. For T-Slot Nuts (DIN 508) in marine, coastal, swimming-pool or food-processing environments, A4 is the default selection.
Comparable Grades
For T-Slot Nuts (DIN 508), the alternative stainless grade is A2 (304). The practical dividing line is chlorides: A2 (304) is fine until salt is involved, and A4 (316) exists for the cases where it is — coastal, marine and road-salt service. Neither reaches the strength of a plated class 8.8 or 10.9 fastener.
Using Stainless Fasteners in Aluminum
The galvanic couple here runs the wrong way: aluminum is the less noble metal, so it corrodes and the fastener does not. What governs the rate is the ratio of areas — a large anode and a small cathode is a tolerable combination, the reverse concentrates the attack into thin material around the hole. An isolating washer plus sealant breaks the circuit; where that is impractical, match the fastener to the substrate.
Sizes of T-Slot Nuts (DIN 508) Available in A4 Stainless Steel
| Size | T-slot width a (mm) | Nut width b (mm) | Total height h (mm) | Neck height k (mm) | Chamfer f (mm) | Reference standard |
|---|---|---|---|---|---|---|
| M4 | 5 | 9 | 6.5 | 3 | 1 | DIN 508 |
| M5 | 6 | 10 | 8 | 4 | 1.6 | DIN 508 |
| M6 | 8 | 13 | 10 | 6 | 1.6 | DIN 508 |
| M8 | 10 | 15 | 12 | 6 | 1.6 | DIN 508 |
| M10 | 12 | 18 | 14 | 7 | 2.5 | DIN 508 |
| M12 | 14 | 22 | 16 | 8 | 2.5 | DIN 508 |
| M16 | 18 | 28 | 20 | 10 | 2.5 | DIN 508 |
| M20 | 22 | 35 | 28 | 14 | 2.5 | DIN 508 |
| M24 | 28 | 44 | 36 | 18 | 4 | DIN 508 |
| M30 | 36 | 54 | 44 | 22 | 6 | DIN 508 |
| M36 | 42 | 65 | 52 | 26 | 6 | DIN 508 |
| M42 | 48 | 75 | 60 | 30 | 6 | DIN 508 |
| M48 | 54 | 85 | 70 | 34 | 6 | DIN 508 |
Dimensions are independent of the material: every size above is available in A4 Stainless Steel.
Custom manufacturing · Made to drawing
Need this nut in a grade that is not listed?
A4 Stainless Steel is one of the grades the catalog describes. Locking method is specifiable independently of the rest: nylon insert, all-metal deformed thread, serrated flange, or none. Made by cold heading or tapping.
Minimum order from 2,000 pieces; samples within 7 days of drawing approval.
