A4 Stainless Steel (A4-80 (316)) is specified for marine, coastal and chemical applications. When taper pins are specified in this grade, the dimensions remain per ISO 2339 / DIN 1; the material determines corrosion behavior (superior, including marine and chloride environments) and the service temperature range (approx. -200 °C to +400 °C). Both are covered below with the size table.
Why Choose A4 Stainless Steel for Taper Pins
Specified for marine, coastal and chemical applications. For taper pins, this matters when superior, including marine and chloride environments is the primary requirement.
Mechanical & Physical Properties
| Grade designation | A4-80 (316) |
|---|---|
| Magnetic response | Largely non-magnetic |
| Service temperature | approx. -200 °C to +400 °C |
| Corrosion characteristic | Superior, including marine and chloride environments |
Galvanic & Galling Considerations
Two important notes for stainless taper pins: (1) stainless can gall on stainless threads under load — use a thread lubricant or anti-galling compound, especially for M6 and below; (2) when joined to aluminum or galvanized steel, stainless can drive galvanic corrosion of the less-noble metal in wet service — isolate with a coating or sleeve where appropriate.
Comparable Grades
For Taper Pins, the alternative stainless grade is A2 (304). A2 (304) suits general indoor and outdoor service; A4 (316) adds molybdenum for marine and chloride environments. Where higher strength matters more than corrosion, switch to plated alloy-steel class 8.8 or 10.9.
Sizes of Taper Pins Available in A4 Stainless Steel
| Small-end diameter (mm) | Taper | Common length range (mm) | Material | Reference standard | Notes |
|---|---|---|---|---|---|
| 0.6 | 1:50 | 4~16 | Carbon steel / stainless | ISO 2339 / DIN 1 (type A) | Large end = small end + length/50 |
| 0.8 | 1:50 | 5~20 | Carbon steel / stainless | ISO 2339 / DIN 1 (type A) | Large end = small end + length/50 |
| 1.0 | 1:50 | 6~25 | Carbon steel / stainless | ISO 2339 / DIN 1 (type A) | Large end = small end + length/50 |
| 1.2 | 1:50 | 6~25 | Carbon steel / stainless | ISO 2339 / DIN 1 (type A) | Large end = small end + length/50 |
| 1.5 | 1:50 | 8~32 | Carbon steel / stainless | ISO 2339 / DIN 1 (type A) | Large end = small end + length/50 |
| 2.0 | 1:50 | 10~45 | Carbon steel / stainless | ISO 2339 / DIN 1 (type A) | Large end = small end + length/50 |
| 2.5 | 1:50 | 12~50 | Carbon steel / stainless | ISO 2339 / DIN 1 (type A) | Large end = small end + length/50 |
| 3.0 | 1:50 | 14~55 | Carbon steel / stainless | ISO 2339 / DIN 1 (type A) | Large end = small end + length/50 |
| 4.0 | 1:50 | 16~70 | Carbon steel / stainless | ISO 2339 / DIN 1 (type A) | Large end = small end + length/50 |
| 5.0 | 1:50 | 18~90 | Carbon steel / stainless | ISO 2339 / DIN 1 (type A) | Large end = small end + length/50 |
| 6.0 | 1:50 | 22~110 | Carbon steel / stainless | ISO 2339 / DIN 1 (type A) | Large end = small end + length/50 |
| 8.0 | 1:50 | 28~140 | Carbon steel / stainless | ISO 2339 / DIN 1 (type A) | Large end = small end + length/50 |
| 10.0 | 1:50 | 35~180 | Carbon steel / stainless | ISO 2339 / DIN 1 (type A) | Large end = small end + length/50 |
| 12.0 | 1:50 | 45~200 | Carbon steel / stainless | ISO 2339 / DIN 1 (type A) | Large end = small end + length/50 |
| 16.0 | 1:50 | 55~200 | Carbon steel / stainless | ISO 2339 / DIN 1 (type A) | Large end = small end + length/50 |
| 20.0 | 1:50 | 65~200 | Carbon steel / stainless | ISO 2339 / DIN 1 (type A) | Large end = small end + length/50 |
| 25.0 | 1:50 | 80~200 | Carbon steel / stainless | ISO 2339 / DIN 1 (type A) | Large end = small end + length/50 |
| 30.0 | 1:50 | 100~200 | Carbon steel / stainless | ISO 2339 / DIN 1 (type A) | Large end = small end + length/50 |
| 40.0 | 1:50 | 120~200 | Carbon steel / stainless | ISO 2339 / DIN 1 (type A) | Large end = small end + length/50 |
| 50.0 | 1:50 | 160~200 | Carbon steel / stainless | ISO 2339 / DIN 1 (type A) | Large end = small end + length/50 |