A4 Stainless Steel (ISO 3506 group A4 (316 / 1.4401), commonly supplied A4-80) is specified for marine, coastal and chemical applications. When thin nylon insert lock nuts (din 985) are specified in this grade, the dimensions remain per DIN 985; the material determines corrosion behavior (superior, including marine and chloride environments) and the service temperature range (approx. -200 °C to +400 °C, subject to the property class and the joint). Both are covered below with the size table.
Why Choose A4 Stainless Steel for Thin Nylon Insert Lock Nuts (DIN 985)
Specified for marine, coastal and chemical applications. For thin nylon insert lock nuts (din 985), this matters when superior, including marine and chloride environments is the primary requirement.
Mechanical & Physical Properties
| Grade designation | ISO 3506 group A4 (316 / 1.4401), commonly supplied A4-80 |
|---|---|
| Magnetic response | Largely non-magnetic |
| Service temperature | approx. -200 °C to +400 °C, subject to the property class and the joint |
| Corrosion characteristic | Superior, including marine and chloride environments |
Galvanic & Galling Considerations
Two important notes for stainless thin nylon insert lock nuts (din 985): (1) stainless can gall on stainless threads under load — use a thread lubricant or anti-galling compound, especially for M6 and below; (2) when joined to aluminum or galvanized steel, stainless can drive galvanic corrosion of the less-noble metal in wet service — isolate with a coating or sleeve where appropriate.
Comparable Grades
For Thin Nylon Insert Lock Nuts (DIN 985), the alternative stainless grade is A2 (304). The practical dividing line is chlorides: A2 (304) is fine until salt is involved, and A4 (316) exists for the cases where it is — coastal, marine and road-salt service. Neither reaches the strength of a plated class 8.8 or 10.9 fastener.
Using Stainless Fasteners in Aluminum
Expect the aluminum to corrode, not the fastener — stainless sits higher in the galvanic series, so the aluminum is the one that gives up material. A small fastener in a thick section spreads the loss over a large area and is usually fine; a large fastener in thin sheet concentrates it and is not. Keep water out of the joint, or isolate the two metals with a nylon or coated washer and a sealant.
Sizes of Thin Nylon Insert Lock Nuts (DIN 985) Available in A4 Stainless Steel
| Thread size | Pitch (mm) | Width across flats s (mm) | Total height m (mm) | Max service temperature (u00b0C) | Re-use | Property class | Reference standard |
|---|---|---|---|---|---|---|---|
| M5 | 0.8 | 8.0 | 5.0 | 120 | 5 cycles typical | 8 | DIN 985 |
| M6 | 1.0 | 10.0 | 6.0 | 120 | 5 cycles typical | 8 | DIN 985 |
| M8 | 1.25 | 13.0 | 8.0 | 120 | 5 cycles typical | 8 | DIN 985 |
| M10 | 1.5 | 17.0 | 10.0 | 120 | 5 cycles typical | 8 | DIN 985 |
| M12 | 1.75 | 19.0 | 12.0 | 120 | 5 cycles typical | 8 | DIN 985 |
| M16 | 2.0 | 24.0 | 16.0 | 120 | 5 cycles typical | 8 | DIN 985 |
Dimensions are independent of the material: every size above is available in A4 Stainless Steel.
Custom manufacturing · Made to drawing
Need this nut in a grade that is not listed?
A4 Stainless Steel is one of the grades the catalog describes. Height and across-flats are the two most often changed — a thinner nut for clearance, a larger hex for a tool that is already on the line. Made by cold heading or tapping.
Minimum order from 2,000 pieces; samples within 7 days of drawing approval.
