Skip to content
info@engineeringhardware.com
WhatsApp
Request a Quote
Seals · Trade series (self-centring bonded washers, USIT type)

EPDM USIT Rings (Self-Centring Bonded Seals)

Temperature range, chemical and fluid compatibility, hardness and the full dimensional range for this compound.

EPDM USIT Rings (Self-Centring Bonded Seals) are supplied to ethylene-propylene-diene rubber, typically 70 Shore A. Corrosion behaviour is excellent in water, steam, brake fluid and weathering; unsuitable for mineral oil, the material is non-magnetic, and the usable service range is approx. -45 °C to +150 °C. In practice this grade is the water, steam and outdoor-weathering elastomer.

Grade
ethylene-propylene-diene rubber, typically 70 Shore A
Corrosion resistance
Excellent in water, steam, brake fluid and weathering; unsuitable for mineral oil
Magnetic response
Non-magnetic
Service temperature
approx. -45 °C to +150 °C

Property values are typical for the grade. Certified mechanical test data is available on request for production orders.

EPDM USIT Rings (Self-Centring Bonded Seals) reference image

Material specification page for usit rings (self-centring bonded seals) in EPDM. Covers the grade designation (ethylene-propylene-diene rubber, typically 70 Shore A), corrosion and magnetic behavior, comparable grades and their trade-offs, and the sizes available to Trade series (self-centring bonded washers, USIT type).

Why Choose EPDM for USIT Rings (Self-Centring Bonded Seals)

The water, steam and outdoor-weathering elastomer. For usit rings (self-centring bonded seals), this matters when excellent in water, steam, brake fluid and weathering; unsuitable for mineral oil is the primary requirement.

Mechanical & Physical Properties

Grade designationethylene-propylene-diene rubber, typically 70 Shore A
Magnetic responseNon-magnetic
Service temperatureapprox. -45 °C to +150 °C
Corrosion characteristicExcellent in water, steam, brake fluid and weathering; unsuitable for mineral oil

Corrosion Behavior in Service

Carbon and alloy steel usit rings (self-centring bonded seals) require a coating for corrosion protection. Zinc plating (with or without passivation) is the most common; hot-dip galvanizing is used for outdoor structural service; black-oxide is mainly a tarnish-prevention finish for tool-room use.

Comparable Grades

For usit rings (self-centring bonded seals), consider NBR for mineral oil and hydraulic service, which EPDM does not tolerate, or silicone for a wider temperature range in static duty. Elastomer selection is decided by the medium, the temperature range and whether the seal is static or dynamic — not by strength.

Sizes of USIT Rings (Self-Centring Bonded Seals) Available in EPDM

ThreadSeal elementMetal carrierTypical service
M6NBR inner lipzinc-plated steelhydraulic ports and plugs
M8NBR inner lipzinc-plated steelhydraulic ports and plugs
M10NBR inner lipzinc-plated steelhydraulic ports and plugs
M12NBR inner lipzinc-plated steelhydraulic ports and plugs
M14NBR or FKM inner lipzinc-plated or stainlesshydraulic and fuel
M16NBR or FKM inner lipzinc-plated or stainlesshydraulic and fuel
M18NBR or FKM inner lipzinc-plated or stainlesshydraulic
M20NBR or FKM inner lipzinc-plated or stainlesshydraulic
M22NBR inner lipzinc-plated steelhydraulic
M27NBR inner lipzinc-plated steelhydraulic

Technical Drawing

Customize the parameters below — every spec field is editable, and the drawing redraws to match the values you choose. Changing the size will snap the other fields to that size's standard values; you can then override any individual value.

Sends the selected values to the quote form below.

Request a Quote

The form below follows the current technical drawing configuration. Change the drawing values above and the request details update automatically.

Request a Quotation

Specification
Business Information

Dimensions & Specifications (Trade series (self-centring bonded washers, USIT type))

ThreadSeal elementMetal carrierTypical service
M6NBR inner lipzinc-plated steelhydraulic ports and plugs
M8NBR inner lipzinc-plated steelhydraulic ports and plugs
M10NBR inner lipzinc-plated steelhydraulic ports and plugs
M12NBR inner lipzinc-plated steelhydraulic ports and plugs
M14NBR or FKM inner lipzinc-plated or stainlesshydraulic and fuel
M16NBR or FKM inner lipzinc-plated or stainlesshydraulic and fuel
M18NBR or FKM inner lipzinc-plated or stainlesshydraulic
M20NBR or FKM inner lipzinc-plated or stainlesshydraulic
M22NBR inner lipzinc-plated steelhydraulic
M27NBR inner lipzinc-plated steelhydraulic

Applications & Industries

USIT Rings are bought for a small number of well-defined jobs. These are the ones we ship them for. Stocked from M6 to M27.

Industries that specify USIT Rings

  • Machine tools Coolant and hydraulic ports.
  • Hydraulics Port plugs and fittings.
  • Mobile plant Vibration-prone joints.
  • Compressors Sealing under pressure cycling.
  • Process & food equipment Sealing at joints that are cleaned and inspected.
  • Hydraulics & pneumatics Static and dynamic sealing in cylinders and valve bodies.

Typical applications

  • seating the ring square before tightening
  • choosing the self-centring form where the seat is imperfect
  • matching the thread size exactly
  • selecting FKM where the fluid or temperature demands it
  • excluding dust and moisture from a housing
  • sealing a joint against fluid or air pressure

Service conditions to specify against

Sealed joints
Used where the fixing has to keep water or air out as well as hold — the elastomer, not the fastener, decides service life.

Where to use something else

  • Do not reuse a bonded or USIT seal after it has been compressed; the elastomer has taken a set and will not seal a second time.

Full application guide: where USIT Rings are used, how to specify them, and the cases they are wrong for

Inside the plant

Manufactured in our own plant

This part is cold-formed, threaded, heat-treated and finished in-house. The stages below are where its class and finish are actually decided.

  1. Wire rod feeding into a cold heading machine
    01

    Cold heading

    Wire rod is drawn to size and cold-formed into blanks. Forming rather than cutting keeps the grain flow continuous around the head, which is where a bolt is most likely to fail.

    Head dimensions and under-head radius checked at set-up and per shift.

  2. Thread rolling machine producing bolt threads
    02

    Thread rolling

    Threads are rolled between hardened dies rather than cut. Rolled threads are stronger in fatigue than cut threads and hold pitch and flank angle far more consistently across a batch.

    Go / no-go ring gauges to ISO 965 tolerance class 6g.

  3. Baskets of bolts staged for heat treatment
    03

    Heat treatment

    Quench-and-temper brings carbon and alloy steel to the property class ordered — 8.8, 10.9 or 12.9 — with the furnace charge tracked so a finished lot can be traced back to it.

    Core hardness and tensile tested per lot to ISO 898-1.

  4. Zinc plated bolts in a treatment basket
    04

    Surface treatment

    Zinc, zinc-nickel, hot-dip galvanizing, black oxide, phosphate and Dacromet, selected against the service environment rather than against the price list.

    Coating thickness and neutral salt spray hours to ISO 9227.

Frequently Asked Questions

What corrosion resistance do EPDM USIT Rings (Self-Centring Bonded Seals) offer?

EPDM USIT Rings (Self-Centring Bonded Seals) provide excellent in water, steam, brake fluid and weathering; unsuitable for mineral oil with a service range of approx. -45 °C to +150 °C.

When should I move from ethylene-propylene-diene rubber, typically 70 Shore A to class 8.8 for USIT Rings (Self-Centring Bonded Seals)?

Step up to class 8.8 when the joint preload approaches the proof load of the current class. The higher class adds preload at the same diameter, often saving size and weight.

Is EPDM prone to hydrogen embrittlement?

Class 10.9 and above can be susceptible to hydrogen embrittlement when electroplated. Specify post-plating baking, or use mechanical-zinc / zinc-flake finishes which avoid the cathodic plating step.

Which finish is best for outdoor USIT Rings (Self-Centring Bonded Seals)?

For outdoor service in steel, hot-dip galvanizing gives the longest life; zinc-flake (Geomet/Delta-Tone family) gives a thinner film with excellent salt-spray performance; standard zinc plating is the lowest-cost option for general indoor / shielded outdoor use.

How do I request a quotation?

Use the technical drawing on this page to pick the exact configuration, then submit it with the quote form. We respond within one business day.