Nuts · Trade series (rubber blind nuts)

Property Class 12.9 Steel EPDM Rubber Well Nuts

Mechanical properties, corrosion behaviour and the full dimensional range for this grade.

Property Class 12.9 Steel EPDM Rubber Well Nuts are supplied to ISO 898-1 property class 12.9. Corrosion behaviour is requires plating or black-oxide protection, the material is magnetic, and the usable service range is commonly limited to approx. +300 °C; confirm against the coating and the load. In practice this grade is the highest common strength class, for high-load machine assembly.

Grade: ISO 898-1 property class 12.9
Corrosion resistance: Requires plating or black-oxide protection
Magnetic response: Magnetic
Service temperature: commonly limited to approx. +300 °C; confirm against the coating and the load

Property values are typical for the grade. Certified mechanical test data is available on request for production orders.

Property Class 12.9 Steel EPDM Rubber Well Nuts combine the dimensional form of Trade series (rubber blind nuts) with the material properties of grade ISO 898-1 property class 12.9: requires plating or black-oxide protection, magnetic, service range commonly limited to approx. +300 °C; confirm against the coating and the load. This page summarizes the grade data, its corrosion behavior in service, the comparable grades, and the sizes supplied.

Why Choose Property Class 12.9 Steel for EPDM Rubber Well Nuts

The highest common strength class, for high-load machine assembly. For epdm rubber well nuts, this matters when requires plating or black-oxide protection is the primary requirement.

Mechanical & Physical Properties

Grade designation	ISO 898-1 property class 12.9
Magnetic response	Magnetic
Service temperature	commonly limited to approx. +300 °C; confirm against the coating and the load
Corrosion characteristic	Requires plating or black-oxide protection

Galvanic & Galling Considerations

For epdm rubber well nuts in steel, the dominant compatibility issue is hydrogen embrittlement at high property classes (10.9 and above) when electroplated. Plating must be followed by an appropriate baking treatment, or a non-electroplated finish (mechanical zinc, zinc flake) should be substituted.

Comparable Grades

For EPDM Rubber Well Nuts, class 8.8 is the comparable strength step. Move up when the joint preload approaches the proof load of the current class; move down when the joint is over-specified. For corrosion-critical service, switch to stainless A2 or A4.

Sizes of EPDM Rubber Well Nuts Available in Property Class 12.9 Steel

Thread size	Representative hole diameter (mm)	Representative grip range (mm)	Temperature range (u00b0C)	Representative tightening torque (Nu00b7m)	Body / insert
M3	8.0	0.4~4.0	-30~+80	0.5	EPDM rubber / stainless threaded insert
M4	8.0	0.4~4.0	-30~+80	0.4	EPDM rubber / stainless threaded insert
M5	9.7	0.4~4.9	-30~+80	0.6	EPDM rubber / stainless threaded insert
M6	12.8	0.4~4.0 or 0.8~4.7	-30~+80	1.0	EPDM rubber / stainless threaded insert
M8	16.0	0.4~4.0	-30~+80	1.5	EPDM rubber / stainless threaded insert

Technical Drawing

Customize the parameters below — every spec field is editable, and the drawing redraws to match the values you choose. Changing the size will snap the other fields to that size's standard values; you can then override any individual value.

Sends the selected values to the quote form below.

Request a Quote

The form below follows the current technical drawing configuration. Change the drawing values above and the request details update automatically.

Request a Quotation

Specification

Item / category Standard Size(s) Material / finish Quantity

Business Information

Company * Contact Name * Email * Phone (with country code) Country / Region

Notes

Dimensions & Specifications (Trade series (rubber blind nuts))

Thread size	Representative hole diameter (mm)	Representative grip range (mm)	Temperature range (u00b0C)	Representative tightening torque (Nu00b7m)	Body / insert
M3	8.0	0.4~4.0	-30~+80	0.5	EPDM rubber / stainless threaded insert
M4	8.0	0.4~4.0	-30~+80	0.4	EPDM rubber / stainless threaded insert
M5	9.7	0.4~4.9	-30~+80	0.6	EPDM rubber / stainless threaded insert
M6	12.8	0.4~4.0 or 0.8~4.7	-30~+80	1.0	EPDM rubber / stainless threaded insert
M8	16.0	0.4~4.0	-30~+80	1.5	EPDM rubber / stainless threaded insert

Applications & Industries

Where EPDM Rubber Well Nuts are used, and what decides the specification in each case. Stocked from M3 to M8.

Industries that specify EPDM Rubber Well Nuts

Vehicle body panels Rubber well nuts isolate and seal trim fasteners through thin skins.
Motorcycle service Blind rubber inserts provide a thread where the rear face is inaccessible.
Outdoor enclosures EPDM accommodates panel movement and keeps a small hole sealed.
Equipment covers Stainless inserts resist corrosion while the rubber body clamps the panel.
Maintenance & MRO Replacements matched to the existing bolt class, thread and finish.
Building services Threaded rod, channel and suspension assemblies.

Typical applications

adding a blind threaded point to a thin panel
matching hole diameter and grip range to the EPDM body
tightening only to the representative torque for the size
using the rubber body for isolation and sealing
completing a bolted joint on a stud, rod or bolt
locking an adjustment so it cannot drift

Service conditions to specify against

Marine and coastal: Available in A4 (316) stainless for chloride exposure — coastal structures, pool halls, water treatment and deck hardware, where A2 will eventually pit.
High load: Supplied in ISO 898-1 property classes, so the joint can be designed to a stated proof load and tightened to a calculated torque rather than by feel.
Sealed joints: Used where the fixing has to keep water or air out as well as hold — the elastomer, not the fastener, decides service life.
Match the class: A nut below the bolt property class strips before the bolt reaches its own limit — pair class 8 nuts with 8.8 bolts, class 10 with 10.9.

Where to use something else

Do not over-tighten a well nut; excess compression can pull the insert through the panel or damage the seal.

Full application guide: where EPDM Rubber Well Nuts are used, how to specify them, and the cases they are wrong for

Inside the plant

Manufactured in our own plant

This part is cold-formed, threaded, heat-treated and finished in-house. The stages below are where its class and finish are actually decided.

01

Cold heading

Wire rod is drawn to size and cold-formed into blanks. Forming rather than cutting keeps the grain flow continuous around the head, which is where a bolt is most likely to fail.

Head dimensions and under-head radius checked at set-up and per shift.
02

Thread rolling

Threads are rolled between hardened dies rather than cut. Rolled threads are stronger in fatigue than cut threads and hold pitch and flank angle far more consistently across a batch.

Go / no-go ring gauges to ISO 965 tolerance class 6g.
03

Heat treatment

Quench-and-temper brings carbon and alloy steel to the property class ordered — 8.8, 10.9 or 12.9 — with the furnace charge tracked so a finished lot can be traced back to it.

Core hardness and tensile tested per lot to ISO 898-1.
04

Surface treatment

Zinc, zinc-nickel, hot-dip galvanizing, black oxide, phosphate and Dacromet, selected against the service environment rather than against the price list.

Coating thickness and neutral salt spray hours to ISO 9227.

Frequently Asked Questions

When should I move from ISO 898-1 property class 12.9 to class 8.8 for EPDM Rubber Well Nuts?

Step up to class 8.8 when the joint preload approaches the proof load of the current class. The higher class adds preload at the same diameter, often saving size and weight.

Is Property Class 12.9 Steel prone to hydrogen embrittlement?

Class 10.9 and above can be susceptible to hydrogen embrittlement when electroplated. Specify post-plating baking, or use mechanical-zinc / zinc-flake finishes which avoid the cathodic plating step.

Which finish is best for outdoor EPDM Rubber Well Nuts?

For outdoor service in steel, hot-dip galvanizing gives the longest life; zinc-flake (Geomet/Delta-Tone family) gives a thinner film with excellent salt-spray performance; standard zinc plating is the lowest-cost option for general indoor / shielded outdoor use.

What's the service temperature limit for Property Class 12.9 Steel?

The practical service range is commonly limited to approx. +300 °C; confirm against the coating and the load.

How do I request a quotation?

Use the technical drawing on this page to pick the exact configuration, then submit it with the quote form. We respond within one business day.