Grade 8.8 Steel (class 8.8) is the workhorse medium-carbon alloy grade for structural joints. When torx recessed countersunk screw are specified in this grade, the dimensions remain per GB/T 2673 / ISO 14587; the material determines corrosion behavior (requires plating (zinc) for corrosion protection) and the service temperature range (up to approx. +300 °C). Both are covered below with the size table.
Why Choose Grade 8.8 Steel for Torx Recessed Countersunk Screw — GB/T 2673 / ISO 14587 (Series 024)
The workhorse medium-carbon alloy grade for structural joints. For torx recessed countersunk screw — gb/t 2673 / iso 14587 (series 024), this matters when requires plating (zinc) for corrosion protection is the primary requirement.
Mechanical & Physical Properties
| Grade designation | class 8.8 |
|---|---|
| Magnetic response | Magnetic |
| Service temperature | up to approx. +300 °C |
| Corrosion characteristic | Requires plating (zinc) for corrosion protection |
Galvanic & Galling Considerations
For torx recessed countersunk screw — gb/t 2673 / iso 14587 (series 024) in steel, the dominant compatibility issue is hydrogen embrittlement at high property classes (10.9 and above) when electroplated. Plating must be followed by an appropriate baking treatment, or a non-electroplated finish (mechanical zinc, zinc flake) should be substituted.
Comparable Grades
For Torx Recessed Countersunk Screw — GB/T 2673 / ISO 14587 (Series 024), class 10.9 or 12.9 is the comparable strength step. Move up when the joint preload approaches the proof load of the current class; move down when the joint is over-specified. For corrosion-critical service, switch to stainless A2 or A4.
Sizes of Torx Recessed Countersunk Screw — GB/T 2673 / ISO 14587 (Series 024) Available in Grade 8.8 Steel
| Size | Pitch (mm) | Length L (mm) | Head diameter dk (mm) | Head height k (mm) | Cross recess | Countersink angle (deg) | Reference standard |
|---|---|---|---|---|---|---|---|
| M3 | 0.5 | 20 | 5.6 | 1.65 | PH1 | 90 | ISO 7046 / GB/T 819 |
| M4 | 0.7 | 25 | 7.5 | 2.2 | PH2 | 90 | ISO 7046 / GB/T 819 |
| M5 | 0.8 | 30 | 9.2 | 2.5 | PH2 | 90 | ISO 7046 / GB/T 819 |
| M6 | 1.0 | 40 | 11.0 | 3.0 | PH3 | 90 | ISO 7046 / GB/T 819 |
| M8 | 1.25 | 50 | 14.5 | 4.0 | PH3 | 90 | ISO 7046 / GB/T 819 |
| M10 | 1.5 | 60 | 18.0 | 5.0 | PH4 | 90 | ISO 7046 / GB/T 819 |
| M12 | 1.75 | 80 | 22.0 | 6.0 | PH4 | 90 | ISO 7046 / GB/T 819 |
| M14 | 2.0 | 80 | 25.0 | 7.0 | PH4 | 90 | ISO 7046 / GB/T 819 |
| M16 | 2.0 | 100 | 29.0 | 8.0 | PH4 | 90 | ISO 7046 / GB/T 819 |
| M18 | 2.5 | 100 | 33.0 | 9.0 | PH4 | 90 | ISO 7046 / GB/T 819 |
| M20 | 2.5 | 120 | 36.5 | 10.0 | PH4 | 90 | ISO 7046 / GB/T 819 |
| M24 | 3.0 | 150 | 43.5 | 12.0 | PH4 | 90 | ISO 7046 / GB/T 819 |