Nylon Insert Hex Lock Nut manufactured in Grade 8.8 Steel (class 8.8) are dimensioned to GB/T 889 / ISO 7040. The sections below give the mechanical and physical properties of the grade, its behavior in corrosive and elevated-temperature service, and the full size table.
Why Choose Grade 8.8 Steel for Nylon Insert Hex Lock Nut — GB/T 889 / ISO 7040 (Series 078)
The workhorse medium-carbon alloy grade for structural joints. For nylon insert hex lock nut — gb/t 889 / iso 7040 (series 078), this matters when requires plating (zinc) for corrosion protection is the primary requirement.
Mechanical & Physical Properties
| Grade designation | class 8.8 |
|---|---|
| Magnetic response | Magnetic |
| Service temperature | up to approx. +300 °C |
| Corrosion characteristic | Requires plating (zinc) for corrosion protection |
Corrosion Behavior in Service
Carbon and alloy steel nylon insert hex lock nut — gb/t 889 / iso 7040 (series 078) require a coating for corrosion protection. Zinc plating (with or without passivation) is the most common; hot-dip galvanizing is used for outdoor structural service; black-oxide is mainly a tarnish-prevention finish for tool-room use.
Comparable Grades
For Nylon Insert Hex Lock Nut — GB/T 889 / ISO 7040 (Series 078), class 10.9 or 12.9 is the comparable strength step. Move up when the joint preload approaches the proof load of the current class; move down when the joint is over-specified. For corrosion-critical service, switch to stainless A2 or A4.
Sizes of Nylon Insert Hex Lock Nut — GB/T 889 / ISO 7040 (Series 078) Available in Grade 8.8 Steel
| Size | Pitch (mm) | Width across flats s (mm) | Width across corners e (mm) | Total height m (mm) | Reference standard |
|---|---|---|---|---|---|
| M3 | 0.5 | 5.5 | 6.01 | 4.0 | ISO 7040 / DIN 985 |
| M4 | 0.7 | 7.0 | 7.66 | 5.0 | ISO 7040 / DIN 985 |
| M5 | 0.8 | 8.0 | 8.79 | 5.0 | ISO 7040 / DIN 985 |
| M6 | 1.0 | 10.0 | 11.05 | 6.0 | ISO 7040 / DIN 985 |
| M8 | 1.25 | 13.0 | 14.38 | 8.0 | ISO 7040 / DIN 985 |
| M10 | 1.5 | 16.0 | 17.77 | 10.0 | ISO 7040 / DIN 985 |
| M12 | 1.75 | 18.0 | 20.03 | 12.0 | ISO 7040 / DIN 985 |
| M14 | 2.0 | 21.0 | 23.36 | 14.0 | ISO 7040 / DIN 985 |
| M16 | 2.0 | 24.0 | 26.75 | 16.0 | ISO 7040 / DIN 985 |
| M18 | 2.5 | 27.0 | 30.14 | 18.0 | ISO 7040 / DIN 985 |
| M20 | 2.5 | 30.0 | 33.53 | 20.0 | ISO 7040 / DIN 985 |
| M24 | 3.0 | 36.0 | 39.98 | 22.0 | ISO 7040 / DIN 985 |
| M30 | 3.5 | 46.0 | 50.85 | 25.0 | ISO 7040 / DIN 985 |
| M36 | 4.0 | 55.0 | 60.79 | 29.0 | ISO 7040 / DIN 985 |