Property Class 8.8 Steel Drilled-Spanner Security Screws are supplied to ISO 898-1 property class 8.8. Corrosion behaviour is requires plating (zinc) for corrosion protection, the material is magnetic, and the usable service range is commonly limited to approx. +300 °C; confirm against the coating and the load. In practice this grade is the workhorse medium-carbon alloy class for structural joints.
- Grade
- ISO 898-1 property class 8.8
- Corrosion resistance
- Requires plating (zinc) for corrosion protection
- Magnetic response
- Magnetic
- Service temperature
- commonly limited to approx. +300 °C; confirm against the coating and the load
Property values are typical for the grade. Certified mechanical test data is available on request for production orders.
Material page for drilled-spanner security screws in Property Class 8.8 Steel (ISO 898-1 property class 8.8). The sizes below are the ones we supply; there is no published dimensional standard for this article, so the table rather than a standard number is what to quote. Corrosion behaviour is requires plating (zinc) for corrosion protection and the service range is commonly limited to approx. +300 °C; confirm against the coating and the load.
Why Choose Property Class 8.8 Steel for Drilled-Spanner Security Screws
The workhorse medium-carbon alloy class for structural joints. For drilled-spanner security screws, this matters when requires plating (zinc) for corrosion protection is the primary requirement.
Mechanical & Physical Properties
| Grade designation | ISO 898-1 property class 8.8 |
|---|
| Magnetic response | Magnetic |
|---|
| Service temperature | commonly limited to approx. +300 °C; confirm against the coating and the load |
|---|
| Corrosion characteristic | Requires plating (zinc) for corrosion protection |
|---|
Corrosion Behavior in Service
Carbon and alloy steel drilled-spanner security screws require a coating for corrosion protection. Zinc plating (with or without passivation) is the most common; hot-dip galvanizing is used for outdoor structural service; black-oxide is mainly a tarnish-prevention finish for tool-room use.
Comparable Grades
For Drilled-Spanner Security Screws, class 10.9 or 12.9 is the comparable strength step. Move up when the joint preload approaches the proof load of the current class; move down when the joint is over-specified. For corrosion-critical service, switch to stainless A2 or A4.
Sizes of Drilled-Spanner Security Screws Available in Property Class 8.8 Steel
| Thread size | Head form | Head diameter (in) | Head height (in) | Length options (in) | Drive | Material |
|---|
| 4-40 undercut | flat 82-degree | 0.225 | 0.047 | 1/4 | two-hole drilled spanner | 18-8 stainless steel |
| 6-32 standard | flat 82-degree | 0.262 | 0.083 | 1/4~2 | two-hole drilled spanner | 18-8 stainless steel |
| 8-32 standard | flat 82-degree | 0.312 | 0.100 | 1/4~2 | two-hole drilled spanner | 18-8 stainless steel |
Dimensions are independent of the material: every size above is available in Property Class 8.8 Steel.
Custom manufacturing · Made to drawing
Need this screw in a grade that is not listed?
Grade 8 8 Steel is one of the grades the catalog describes. Where the standard stops, the drawing takes over: fine pitches, left-hand threads, partial threading, and property classes above the catalogued grade where material and heat treatment allow. Made by cold heading or warm forging.
Minimum order from 2,000 pieces; samples within 7 days of drawing approval.
Custom screw manufacturingSend a drawing
Applications & Industries
Where Drilled-Spanner Security Screws are used, and what decides the specification in each case. Stocked from 4-40 undercut to 8-32 standard (nominal diameter).
Industries that specify Drilled-Spanner Security Screws
-
Public fixtures
Two-hole drives resist common screwdrivers and casual tampering.
-
Washroom equipment
Stainless flat-head forms keep visible panels flush.
-
Retail displays
Special drive hardware slows unauthorized removal.
-
Equipment enclosures
4-40 through 8-32 examples fit small service panels.
-
Steel fabrication
Bolted connections in frames, enclosures, walkways and weldments, on the bench and on site.
-
Energy & infrastructure
Tower, pipework, switchgear and plant fixings specified for long service life and inspectable joints.
Typical applications
- installing a two-hole drilled-spanner security screw
- matching the 82-degree flat head to the countersink
- selecting the undercut or standard head by panel thickness
- keeping the matching driver for authorized service
- clamping two machined faces to a calculated preload
- bolting brackets, motors and gearboxes to a frame
Service conditions to specify against
- Marine and coastal
- Available in A4 (316) stainless for chloride exposure — coastal structures, pool halls, water treatment and deck hardware, where A2 will eventually pit.
- High load
- Supplied in ISO 898-1 property classes, so the joint can be designed to a stated proof load and tightened to a calculated torque rather than by feel.
- Torque and preload
- The joint is designed around bolt tension, so lubrication, coating and the friction coefficient all change the torque figure — state them together.
Where to use something else
- Do not substitute a standard Phillips driver; the two-hole recess is the tamper-resistance feature.
- Do not use a machine thread into unthreaded sheet or timber; use a tapping screw, rivet nut or insert made for that parent material.
Full application guide: where Drilled-Spanner Security Screws are used, how to specify them, and the cases they are wrong for