Property Class 8.8 Steel Micro Miniature Small Pan-Head Phillips Machine Screws are supplied to ISO 898-1 property class 8.8. Corrosion behaviour is requires plating (zinc) for corrosion protection, the material is magnetic, and the usable service range is commonly limited to approx. +300 °C; confirm against the coating and the load. In practice this grade is the workhorse medium-carbon alloy class for structural joints.
- Grade
- ISO 898-1 property class 8.8
- Corrosion resistance
- Requires plating (zinc) for corrosion protection
- Magnetic response
- Magnetic
- Service temperature
- commonly limited to approx. +300 °C; confirm against the coating and the load
Property values are typical for the grade. Certified mechanical test data is available on request for production orders.
Property Class 8.8 Steel (ISO 898-1 property class 8.8) is the workhorse medium-carbon alloy class for structural joints. Specified on micro miniature small pan-head phillips machine screws it determines the corrosion behaviour (requires plating (zinc) for corrosion protection) and the service temperature range (commonly limited to approx. +300 °C; confirm against the coating and the load); the dimensions are ours rather than a standard's, and are listed in full below.
Why Choose Property Class 8.8 Steel for Micro Miniature Small Pan-Head Phillips Machine Screws
The workhorse medium-carbon alloy class for structural joints. For micro miniature small pan-head phillips machine screws, this matters when requires plating (zinc) for corrosion protection is the primary requirement.
Mechanical & Physical Properties
| Grade designation | ISO 898-1 property class 8.8 |
|---|
| Magnetic response | Magnetic |
|---|
| Service temperature | commonly limited to approx. +300 °C; confirm against the coating and the load |
|---|
| Corrosion characteristic | Requires plating (zinc) for corrosion protection |
|---|
Corrosion Behavior in Service
Carbon and alloy steel micro miniature small pan-head phillips machine screws require a coating for corrosion protection. Zinc plating (with or without passivation) is the most common; hot-dip galvanizing is used for outdoor structural service; black-oxide is mainly a tarnish-prevention finish for tool-room use.
Galvanic & Galling Considerations
For micro miniature small pan-head phillips machine screws in steel, the dominant compatibility issue is hydrogen embrittlement at high property classes (10.9 and above) when electroplated. Plating must be followed by an appropriate baking treatment, or a non-electroplated finish (mechanical zinc, zinc flake) should be substituted.
Sizes of Micro Miniature Small Pan-Head Phillips Machine Screws Available in Property Class 8.8 Steel
| Thread size | Head diameter (mm) | Head height (mm) | Typical length range (mm) | Drive | Material options |
|---|
| M0.6 | 1.2 | 0.35 | 2~20 | miniature cross recess | zinc-plated / black-plated / nickel-plated steel; A2/316 stainless; brass |
| M0.8 | 1.6 | 0.40 | 2~20 | miniature cross recess | zinc-plated / black-plated / nickel-plated steel; A2/316 stainless; brass |
| M1.0 | 1.8 | 0.45 | 2~20 | miniature cross recess | zinc-plated / black-plated / nickel-plated steel; A2/316 stainless; brass |
| M1.2 | 3.5 | 0.45 | 2~20 | miniature cross recess | zinc-plated / black-plated / nickel-plated steel; A2/316 stainless; brass |
Dimensions are independent of the material: every size above is available in Property Class 8.8 Steel.
Custom manufacturing · Made to drawing
Need this screw in a grade that is not listed?
Grade 8 8 Steel is one of the grades the catalog describes. Where the standard stops, the drawing takes over: fine pitches, left-hand threads, partial threading, and property classes above the catalogued grade where material and heat treatment allow. Made by cold heading or warm forging.
Minimum order from 2,000 pieces; samples within 7 days of drawing approval.
Custom screw manufacturingSend a drawing
Applications & Industries
The sectors that buy Micro Miniature Small Pan-Head Phillips Machine Screws, and the duty each one buys them for. Stocked from M0.6 to M1.2.
Industries that specify Micro Miniature Small Pan-Head Phillips Machine Screws
-
Instrument production
Short cross-drive screws hold compact housings and sensor covers.
-
Optical equipment
Miniature hardware secures light components without a large head envelope.
-
Repair benches
Stocked micro sizes replace stripped fasteners in precision devices.
-
Microelectronics
Small pan heads mount shields and brackets where a standard head would crowd the assembly.
-
Food, pharma & cleanroom
Stainless assemblies that are washed down, where the finish matters as much as the strength.
-
Machine building & OEM
The default fastener on production equipment: covers, brackets, motor mounts and sub-assemblies tightened to a specified torque.
Typical applications
- matching head diameter and height to the component clearance
- choosing plated steel, stainless steel or brass for the service environment
- keeping the driver axial so the miniature recess is not stripped
- securing miniature covers with a small Phillips recess
- bolting brackets, motors and gearboxes to a frame
- assemblies that are dismantled for service and re-torqued
Service conditions to specify against
- Marine and coastal
- Available in A4 (316) stainless for chloride exposure — coastal structures, pool halls, water treatment and deck hardware, where A2 will eventually pit.
- High load
- Supplied in ISO 898-1 property classes, so the joint can be designed to a stated proof load and tightened to a calculated torque rather than by feel.
- Torque and preload
- The joint is designed around bolt tension, so lubrication, coating and the friction coefficient all change the torque figure — state them together.
Where to use something else
- Do not substitute a standard M2 screw when the head envelope or thread length is controlled by the miniature assembly.
- Do not use a machine thread into unthreaded sheet or timber; use a tapping screw, rivet nut or insert made for that parent material.
Full application guide: where Micro Miniature Small Pan-Head Phillips Machine Screws are used, how to specify them, and the cases they are wrong for