Property Class 8.8 Steel (ISO 898-1 property class 8.8) is the workhorse medium-carbon alloy class for structural joints. When nyloc lock nuts are specified in this grade, the dimensions remain per DIN 985 / ISO 7040; the material determines corrosion behavior (requires plating (zinc) for corrosion protection) and the service temperature range (commonly limited to approx. +300 °C; confirm against the coating and the load). Both are covered below with the size table.
Why Choose Property Class 8.8 Steel for Nyloc Lock Nuts
The workhorse medium-carbon alloy class for structural joints. For nyloc lock nuts, this matters when requires plating (zinc) for corrosion protection is the primary requirement.
Mechanical & Physical Properties
| Grade designation | ISO 898-1 property class 8.8 |
|---|---|
| Magnetic response | Magnetic |
| Service temperature | commonly limited to approx. +300 °C; confirm against the coating and the load |
| Corrosion characteristic | Requires plating (zinc) for corrosion protection |
Galvanic & Galling Considerations
For nyloc lock nuts in steel, the dominant compatibility issue is hydrogen embrittlement at high property classes (10.9 and above) when electroplated. Plating must be followed by an appropriate baking treatment, or a non-electroplated finish (mechanical zinc, zinc flake) should be substituted.
Comparable Grades
For Nyloc Lock Nuts, class 10.9 or 12.9 is the comparable strength step. Move up when the joint preload approaches the proof load of the current class; move down when the joint is over-specified. For corrosion-critical service, switch to stainless A2 or A4.
Sizes of Nyloc Lock Nuts Available in Property Class 8.8 Steel
| Size | Pitch (mm) | Width across flats s (mm) | Width across corners e min (mm) | Total height m (mm) | Metal height (mm) | Reference standard | Notes |
|---|---|---|---|---|---|---|---|
| M3 | 0.5 | 5.5 | 6.01 | 4.0 | 2.4 | DIN 985 / ISO 7040 | With nylon insert, single use |
| M4 | 0.7 | 7.0 | 7.66 | 5.0 | 3.2 | DIN 985 / ISO 7040 | With nylon insert, single use |
| M5 | 0.8 | 8.0 | 8.79 | 5.0 | 3.7 | DIN 985 / ISO 7040 | With nylon insert, single use |
| M6 | 1.0 | 10.0 | 11.05 | 6.0 | 4.7 | DIN 985 / ISO 7040 | With nylon insert, single use |
| M8 | 1.25 | 13.0 | 14.38 | 8.0 | 6.14 | DIN 985 / ISO 7040 | With nylon insert, single use |
| M10 | 1.5 | 16.0 | 17.77 | 10.0 | 8.04 | DIN 985 / ISO 7040 | With nylon insert, single use |
| M12 | 1.75 | 18.0 | 20.03 | 12.0 | 9.64 | DIN 985 / ISO 7040 | With nylon insert, single use |
| M14 | 2.0 | 21.0 | 23.36 | 14.0 | 11.0 | DIN 985 / ISO 7040 | With nylon insert, single use |
| M16 | 2.0 | 24.0 | 26.75 | 16.0 | 13.0 | DIN 985 / ISO 7040 | With nylon insert, single use |
| M20 | 2.5 | 30.0 | 32.95 | 20.0 | 16.0 | DIN 985 / ISO 7040 | With nylon insert, single use |
| M24 | 3.0 | 36.0 | 39.55 | 22.0 | 19.0 | DIN 985 / ISO 7040 | With nylon insert, single use |
| M30 | 3.5 | 46.0 | 50.85 | 25.0 | 24.0 | DIN 985 / ISO 7040 | With nylon insert, single use |
| M36 | 4.0 | 55.0 | 60.79 | 29.0 | 29.0 | DIN 985 / ISO 7040 | With nylon insert, single use |
