Material specification page for pan head screws in Grade 8.8 Steel. Covers the grade designation (class 8.8), corrosion and magnetic behavior, comparable grades and their trade-offs, and the sizes available to ISO 1207 / ISO 7045 / DIN 7985.
Why Choose Grade 8.8 Steel for Pan Head Screws
The workhorse medium-carbon alloy grade for structural joints. For pan head screws, this matters when requires plating (zinc) for corrosion protection is the primary requirement.
Mechanical & Physical Properties
| Grade designation | class 8.8 |
|---|---|
| Magnetic response | Magnetic |
| Service temperature | up to approx. +300 °C |
| Corrosion characteristic | Requires plating (zinc) for corrosion protection |
Corrosion Behavior in Service
Carbon and alloy steel pan head screws require a coating for corrosion protection. Zinc plating (with or without passivation) is the most common; hot-dip galvanizing is used for outdoor structural service; black-oxide is mainly a tarnish-prevention finish for tool-room use.
Comparable Grades
For Pan Head Screws, class 10.9 or 12.9 is the comparable strength step. Move up when the joint preload approaches the proof load of the current class; move down when the joint is over-specified. For corrosion-critical service, switch to stainless A2 or A4.
Sizes of Pan Head Screws Available in Grade 8.8 Steel
| Size | Pitch (mm) | Head diameter dk (mm) | Head height k (mm) | Cross recess | Reference standard |
|---|---|---|---|---|---|
| M1 | 0.25 | 2.0 | 0.8 | PH0 | ISO 1207 / ISO 7045 / DIN 7985 |
| M1.2 | 0.25 | 2.3 | 0.9 | PH0 | ISO 1207 / ISO 7045 / DIN 7985 |
| M1.4 | 0.3 | 2.6 | 1.0 | PH0 | ISO 1207 / ISO 7045 / DIN 7985 |
| M1.6 | 0.35 | 3.0 | 1.0 | PH0 | ISO 1207 / ISO 7045 / DIN 7985 |
| M2 | 0.4 | 3.8 | 1.3 | PH1 | ISO 1207 / ISO 7045 / DIN 7985 |
| M2.5 | 0.45 | 4.7 | 1.5 | PH1 | ISO 1207 / ISO 7045 / DIN 7985 |
| M3 | 0.5 | 5.6 | 1.8 | PH1 | ISO 1207 / ISO 7045 / DIN 7985 |
| M3.5 | 0.6 | 6.5 | 2.1 | PH2 | ISO 1207 / ISO 7045 / DIN 7985 |
| M4 | 0.7 | 8.0 | 2.4 | PH2 | ISO 1207 / ISO 7045 / DIN 7985 |
| M5 | 0.8 | 9.5 | 3.0 | PH2 | ISO 1207 / ISO 7045 / DIN 7985 |
| M6 | 1.0 | 12.0 | 3.6 | PH3 | ISO 1207 / ISO 7045 / DIN 7985 |
| M8 | 1.25 | 16.0 | 4.8 | PH3 | ISO 1207 / ISO 7045 / DIN 7985 |
| M10 | 1.5 | 20.0 | 6.0 | PH4 | ISO 1207 / ISO 7045 / DIN 7985 |