Property Class 8.8 Steel Structural Blind Bolts are supplied to ISO 898-1 property class 8.8. Corrosion behaviour is requires plating (zinc) for corrosion protection, the material is magnetic, and the usable service range is commonly limited to approx. +300 °C; confirm against the coating and the load. In practice this grade is the workhorse medium-carbon alloy class for structural joints.
- Grade
- ISO 898-1 property class 8.8
- Corrosion resistance
- Requires plating (zinc) for corrosion protection
- Magnetic response
- Magnetic
- Service temperature
- commonly limited to approx. +300 °C; confirm against the coating and the load
Property values are typical for the grade. Certified mechanical test data is available on request for production orders.
Material page for structural blind bolts in Property Class 8.8 Steel (ISO 898-1 property class 8.8). The sizes below are the ones we supply; there is no published dimensional standard for this article, so the table rather than a standard number is what to quote. Corrosion behaviour is requires plating (zinc) for corrosion protection and the service range is commonly limited to approx. +300 °C; confirm against the coating and the load.
Why Choose Property Class 8.8 Steel for Structural Blind Bolts
The workhorse medium-carbon alloy class for structural joints. For structural blind bolts, this matters when requires plating (zinc) for corrosion protection is the primary requirement.
Mechanical & Physical Properties
| Grade designation | ISO 898-1 property class 8.8 |
|---|
| Magnetic response | Magnetic |
|---|
| Service temperature | commonly limited to approx. +300 °C; confirm against the coating and the load |
|---|
| Corrosion characteristic | Requires plating (zinc) for corrosion protection |
|---|
Corrosion Behavior in Service
Carbon and alloy steel structural blind bolts require a coating for corrosion protection. Zinc plating (with or without passivation) is the most common; hot-dip galvanizing is used for outdoor structural service; black-oxide is mainly a tarnish-prevention finish for tool-room use.
Comparable Grades
For Structural Blind Bolts, class 10.9 or 12.9 is the comparable strength step. Move up when the joint preload approaches the proof load of the current class; move down when the joint is over-specified. For corrosion-critical service, switch to stainless A2 or A4.
Sizes of Structural Blind Bolts Available in Property Class 8.8 Steel
| Stem | Rated for | Access | Distinguished from |
|---|
| mechanically locked, retained | structural shear and tension | one side only | an ordinary blind rivet, whose stem is not retained |
| mechanically locked, retained, countersunk | structural shear and tension | one side only | an ordinary blind rivet, whose stem is not retained |
Dimensions are independent of the material: every size above is available in Property Class 8.8 Steel.
Custom manufacturing · Made to drawing
Need this bolt in a grade that is not listed?
Grade 8 8 Steel is one of the grades the catalog describes. Material and finish are usually what drives a special — a grade the standard part is not stocked in, or a coating chosen against a salt-spray figure instead of a default. Made by cold heading or hot forging.
Minimum order from 2,000 pieces; samples within 7 days of drawing approval.
Custom bolt manufacturingSend a drawing
Applications & Industries
Structural Blind Bolts are bought for a small number of well-defined jobs. These are the ones we ship them for. Stocked from mechanically locked, retained to mechanically locked, retained, countersunk (nominal diameter).
Industries that specify Structural Blind Bolts
-
Bridge and infrastructure
Retained-stem shear capacity.
-
Structural steel
Shear-rated blind connections.
-
Rail vehicles
Blind structural joints in bodyshells.
-
Container and trailer build
One-side structural fastening.
-
Energy & infrastructure
Tower, pipework, switchgear and plant fixings specified for long service life and inspectable joints.
-
Maintenance & MRO
Stocked replacements matched to an existing property class, thread and finish.
Typical applications
- checking the set fastener for a flush, locked stem
- confirming the stem is mechanically locked and retained
- matching grip range to the ply thickness
- using the correct setting tool and nose assembly
- joints where the property class is stated on the drawing
- clamping two machined faces to a calculated preload
Service conditions to specify against
- Marine and coastal
- Available in A4 (316) stainless for chloride exposure — coastal structures, pool halls, water treatment and deck hardware, where A2 will eventually pit.
- High load
- Supplied in ISO 898-1 property classes, so the joint can be designed to a stated proof load and tightened to a calculated torque rather than by feel.
- Vibration
- Specified where cyclic load would loosen a plain nut or screw — rotating plant, rail, mobile equipment and anything that is not re-torqued in service.
- Torque and preload
- The joint is designed around bolt tension, so lubrication, coating and the friction coefficient all change the torque figure — state them together.
Where to use something else
- Do not substitute an ordinary blind rivet; without a retained stem there is nothing carrying the shear.
- Do not use a machine thread into unthreaded sheet or timber; use a tapping screw, rivet nut or insert made for that parent material.
Full application guide: where Structural Blind Bolts are used, how to specify them, and the cases they are wrong for
