Dimensional and assembly data for M1.2 Slotted Set Screws with Cone Point to ISO 7434. Includes head size and width across flats, clearance-hole and tapping-drill diameters, tightening torque per property class, and the sizes to step up or down to when the joint requires it.
M1.2 Dimensional Row (ISO 7434)
| Size | dt_max (mm) | n_nom (mm) | n_min (mm) | n_max (mm) | t_nom_min (mm) | t_max (mm) | Length range l (mm) | Reference standard |
|---|---|---|---|---|---|---|---|---|
| M1.2 | 0.12 | 0.2 | 0.26 | 0.4 | 0.4 | 0.52 | 2~6 | ISO 7434 |
Spanner & Drive for M1.2 Slotted Set Screws with Cone Point
The hex socket for M1.2 Slotted Set Screws with Cone Point is shown in the spec table — use the matching Allen / hex key (an ISO 2936 hex key set covers the full range). Ball-end keys are for reaching the screw, not for tightening it — finish on the plain end, and on production work use a torque-controlled driver.
Hole Sizes for M1.2
| Coarse-thread pitch (ISO 724) | 0.25 mm |
|---|---|
| Through-hole / clearance (ISO 273 medium) | 1.4 mm |
| Tapping drill, coarse thread | 0.95 mm |
Tightening Torque for M1.2
| Class 8.8 (dry, ~µ 0.125) | ≈ Nm |
|---|---|
| Class 10.9 (dry, ~µ 0.125) | ≈ Nm |
| Class 12.9 (dry, ~µ 0.125) | ≈ Nm |
Indicative dry-joint values. Lubrication can lower the required torque by 15–25%. Always confirm against the joint design, especially when going up a strength class.
Proof Load & Strength for M1.2
Set screws are rated to ISO 898-5 by hardness, because they work in compression against a shaft rather than in tension. ISO 898-1 excludes them, and a set screw has no head to preload against, so neither a property class nor a preload torque applies. Seating torque depends on the point form and the shaft material.
M1.2 Slotted Set Screws with Cone Point Weight
A steel M1.2 slotted set screws with cone point at the listed 26 mm length weighs approximately 0.2 g each — about 0.2 kg per 1,000 pieces. Stainless A2/A4 weighs roughly the same (density 7.9–8.0 g/cm³).
Actual weight varies slightly with head form, thread and finish; use this figure for freight estimation only.
Installation Tips for M1.2 Slotted Set Screws with Cone Point
- Use a quality Allen key fully seated in the socket — partial engagement is the most common cause of stripped sockets at this size.
- For countersunk and button-head variants, chamfer the through-hole to seat the head flush without preloading the head/shank fillet.
- At M1.2 the joint is sensitive to over-torque — use a torque-limiting driver and check the head doesn't bury into a softer counterpart.
Mating Parts for M1.2
For M1.2, pair with a M1.2 hex nut (ISO 4032 / DIN 934) and, where used, a M1.2 flat washer (ISO 7089 / DIN 125A) under the head and under the nut.
Custom manufacturing · Made to drawing
Need slotted set screws with cone point in a size this table does not list?
This page covers M1.2 slotted set screws with cone point. Where the standard stops, the drawing takes over: fine pitches, left-hand threads, partial threading, and property classes above the catalogued grade where material and heat treatment allow. Made by cold heading or warm forging.
Minimum order from 2,000 pieces; samples within 7 days of drawing approval.
