The M10 size of Socket Head Cap Screw is dimensioned by GB/T 5281 / ISO 7379. The tables below give the dimensional row from the standard, the drill and spanner sizes that go with it, and the assembly torque per property class. The technical drawing on this page redraws to the exact values selected.
M10 Dimensional Row (GB/T 5281 / ISO 7379)
| Size | Pitch (mm) | Length L (mm) | Head diameter dk (mm) | Head height k (mm) | Hex socket s (mm) | Reference standard |
|---|---|---|---|---|---|---|
| M10 | 1.5 | 60 | 16.0 | 10 | 8.0 | ISO 4762 / GB/T 70.1 |
Spanner & Drive for M10 Socket Head Cap Screw — GB/T 5281 / ISO 7379 (Series 015)
The hex socket for M10 Socket Head Cap Screw — GB/T 5281 / ISO 7379 (Series 015) is shown in the spec table — use the matching Allen / hex key (an ISO 2936 hex key set covers the full range). A T-handle Allen key gives the best feel for setting preload by feel; for production work use a torque-controlled driver.
Hole Sizes for M10
| Coarse-thread pitch (ISO 724) | 1.5 mm |
|---|---|
| Through-hole / clearance (ISO 273 medium) | 11 mm |
| Tapping drill, coarse thread | 8.5 mm |
Tightening Torque for M10
| Class 8.8 (dry, ~µ 0.125) | ≈ 49 Nm |
|---|---|
| Class 10.9 (dry, ~µ 0.125) | ≈ 69 Nm |
| Class 12.9 (dry, ~µ 0.125) | ≈ 83 Nm |
Indicative dry-joint values. Lubrication can lower the required torque by 15–25%. Always confirm against the joint design, especially when going up a strength class.
Proof Load & Strength for M10
| Tensile stress area As (ISO 898-1) | 58 mm² |
|---|---|
| Proof load, class 8.8 | 34 kN |
| Proof load, class 10.9 | 48 kN |
| Proof load, class 12.9 | 56 kN |
| Min. ultimate tensile, class 8.8 | 46 kN |
Proof load = stress area × proof stress per ISO 898-1. Design joints so the working preload stays below the proof load of the selected class.
M10 Socket Head Cap Screw — GB/T 5281 / ISO 7379 (Series 015) Weight
A steel M10 socket head cap screw at the listed 60 mm length weighs approximately 95 g each — about 95 kg per 1,000 pieces. Stainless A2/A4 weighs roughly the same (density 7.9–8.0 g/cm³). Actual weight varies slightly with head form, thread and finish; use this figure for freight estimation only.
Common Applications for M10 Socket Head Cap Screw — GB/T 5281 / ISO 7379 (Series 015)
M10 Socket Head Cap Screw — GB/T 5281 / ISO 7379 (Series 015) are commonly specified for machine assembly, general engineering, plant maintenance and OEM equipment.
Installation Tips for M10 Socket Head Cap Screw — GB/T 5281 / ISO 7379 (Series 015)
- Use a quality Allen key fully seated in the socket — partial engagement is the most common cause of stripped sockets at this size.
- For countersunk and button-head variants, chamfer the through-hole to seat the head flush without preloading the head/shank fillet.
When to Step Up or Down from M10
When the joint preload approaches the proof load of M10 class 8.8, step up to M12 class 8.8 (or move to M10 class 10.9). When the joint is over-specified, M8 often saves weight and cost without losing the safety margin.