M10 is one of the standard coarse-thread sizes for low head socket cap screws under DIN 7984. The sections below reproduce the dimensional row, list the matching tools and hole sizes, and summarize where this size is normally specified.
M10 Dimensional Row (DIN 7984)
| Size | Pitch P (mm) | b (mm) | Head diameter dk (mm) | da (mm) | ds_min (mm) | e (mm) | Head height k (mm) | r (mm) | Hex socket s (mm) | t (mm) | v (mm) | dw (mm) | Length range l (mm) | Reference standard |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| M10 | 1.5 | 26 | 16.0 | 11.2 | 9.78 | 8.01 | 6.0 | 0.4 | 7.0 | 4.5 | 1.0 | 15.03 | 16~70 | DIN 7984 |
Spanner & Drive for M10 Low Head Socket Cap Screws
The hex socket for M10 Low Head Socket Cap Screws is shown in the spec table — use the matching Allen / hex key (an ISO 2936 hex key set covers the full range). For a one-off, a T-handle key and a calibrated arm will do. For a batch, the only way to get the same preload twice is a torque-controlled driver.
Hole Sizes for M10
| Coarse-thread pitch (ISO 724) | 1.5 mm |
|---|---|
| Through-hole / clearance (ISO 273 medium) | 11 mm |
| Tapping drill, coarse thread | 8.5 mm |
Tightening Torque for M10
| Class 8.8 (dry, ~µ 0.125) | ≈ 48 Nm |
|---|---|
| Class 10.9 (dry, ~µ 0.125) | ≈ 71 Nm |
| Class 12.9 (dry, ~µ 0.125) | ≈ 83 Nm |
Indicative dry-joint values. Lubrication can lower the required torque by 15–25%. Always confirm against the joint design, especially when going up a strength class.
Proof Load & Strength for M10
This is a reduced-height head. The head, not the thread, limits what the screw will carry — ISO 7380-1 caps a button head at roughly 80% of the thread's capacity — so the thread's proof load overstates the assembly. Size the joint on the head, or use a cap screw where the full class strength is needed.
M10 Low Head Socket Cap Screws Weight
A steel M10 low head socket cap screws at the listed 1,670 mm length weighs approximately 2,636 g each — about 2,636 kg per 1,000 pieces. Stainless A2/A4 weighs roughly the same (density 7.9–8.0 g/cm³).
Actual weight varies slightly with head form, thread and finish; use this figure for freight estimation only.
Installation Tips for M10 Low Head Socket Cap Screws
- Use a quality Allen key fully seated in the socket — partial engagement is the most common cause of stripped sockets at this size.
- For countersunk and button-head variants, chamfer the through-hole to seat the head flush without preloading the head/shank fillet.
Mating Parts for M10
For M10, pair with a M10 hex nut (ISO 4032 / DIN 934) and, where used, a M10 flat washer (ISO 7089 / DIN 125A) under the head and under the nut.
Custom manufacturing · Made to drawing
Need low head socket cap screws in a size this table does not list?
This page covers M10 low head socket cap screws. Where the standard stops, the drawing takes over: fine pitches, left-hand threads, partial threading, and property classes above the catalogued grade where material and heat treatment allow. Made by cold heading or warm forging.
Minimum order from 2,000 pieces; samples within 7 days of drawing approval.
