The M14 size of Hex Bolt is dimensioned by GB/T 5782 / ISO 4014. The tables below give the dimensional row from the standard, the drill and spanner sizes that go with it, and the assembly torque per property class. The technical drawing on this page redraws to the exact values selected.
M14 Dimensional Row (GB/T 5782 / ISO 4014)
| Size | Pitch (mm) | Nominal diameter d (mm) | Length L (mm) | Width across flats s (mm) | Width across corners e (mm) | Head height k (mm) |
|---|---|---|---|---|---|---|
| M14 | 2.0 | 14 | 80 | 21.0 | 23.36 | 8.8 |
Spanner & Drive for M14 Hex Bolt — GB/T 5782 / ISO 4014 (Series 006)
M14 Hex Bolt — GB/T 5782 / ISO 4014 (Series 006) have a width across flats of 21.0 mm — fit a 21.0 mm open-ended spanner or socket. Use a 6-point socket for tight clearances and to reduce rounding; for repeated assembly choose a torque wrench so the joint preload is repeatable.
Hole Sizes for M14
| Coarse-thread pitch (ISO 724) | 2 mm |
|---|---|
| Through-hole / clearance (ISO 273 medium) | 15.5 mm |
| Tapping drill, coarse thread | 12 mm |
Tightening Torque for M14
| Class 8.8 (dry, ~µ 0.125) | ≈ 135 Nm |
|---|---|
| Class 10.9 (dry, ~µ 0.125) | ≈ 190 Nm |
| Class 12.9 (dry, ~µ 0.125) | ≈ 230 Nm |
Indicative dry-joint values. Lubrication can lower the required torque by 15–25%. Always confirm against the joint design, especially when going up a strength class.
Proof Load & Strength for M14
| Tensile stress area As (ISO 898-1) | 115 mm² |
|---|---|
| Proof load, class 8.8 | 67 kN |
| Proof load, class 10.9 | 95 kN |
| Proof load, class 12.9 | 112 kN |
| Min. ultimate tensile, class 8.8 | 92 kN |
Proof load = stress area × proof stress per ISO 898-1. Design joints so the working preload stays below the proof load of the selected class.
M14 Hex Bolt — GB/T 5782 / ISO 4014 (Series 006) Weight
A steel M14 hex bolt at the listed 80 mm length weighs approximately 123 g each — about 123 kg per 1,000 pieces. Stainless A2/A4 weighs roughly the same (density 7.9–8.0 g/cm³). Actual weight varies slightly with head form, thread and finish; use this figure for freight estimation only.
Common Applications for M14 Hex Bolt — GB/T 5782 / ISO 4014 (Series 006)
M14 Hex Bolt — GB/T 5782 / ISO 4014 (Series 006) are commonly specified for medium-duty structural connections, automotive sub-frames and equipment chassis.
Installation Tips for M14 Hex Bolt — GB/T 5782 / ISO 4014 (Series 006)
- Use a 6-point socket where access allows — 12-point sockets are more prone to rounding the corners on smaller sizes.
- On flanged or serrated variants, do NOT add a separate flat washer — the flange already spreads the load and the washer can defeat the locking serrations.
Mating Parts for M14
For M14, pair with a M14 hex nut (ISO 4032 / DIN 934) and, where used, a M14 flat washer (ISO 7089 / DIN 125A) under the head and under the nut.