Dimensional and assembly data for M16 Hex Bolt to GB/T 5783 / ISO 4017. Includes head size and width across flats, clearance-hole and tapping-drill diameters, tightening torque per property class, and the sizes to step up or down to when the joint requires it.
M16 Dimensional Row (GB/T 5783 / ISO 4017)
| Size | Pitch (mm) | Nominal diameter d (mm) | Length L (mm) | Width across flats s (mm) | Width across corners e (mm) | Head height k (mm) |
|---|---|---|---|---|---|---|
| M16 | 2.0 | 16 | 100 | 24.0 | 26.75 | 10.0 |
Spanner & Drive for M16 Hex Bolt — GB/T 5783 / ISO 4017 (Series 010)
M16 Hex Bolt — GB/T 5783 / ISO 4017 (Series 010) have a width across flats of 24.0 mm — fit a 24.0 mm open-ended spanner or socket. A 6-point socket grips all six flats of the 24.0 mm hex and is what to reach for once a fastener has been on and off a few times; a 12-point ring spanner starts rounding a worn head. For repeatable preload, torque rather than feel.
Hole Sizes for M16
| Coarse-thread pitch (ISO 724) | 2 mm |
|---|---|
| Through-hole / clearance (ISO 273 medium) | 17.5 mm |
| Tapping drill, coarse thread | 14 mm |
Tightening Torque for M16
| Class 8.8 (dry, ~µ 0.125) | ≈ 209 Nm |
|---|---|
| Class 10.9 (dry, ~µ 0.125) | ≈ 306 Nm |
| Class 12.9 (dry, ~µ 0.125) | ≈ 358 Nm |
Indicative dry-joint values. Lubrication can lower the required torque by 15–25%. Always confirm against the joint design, especially when going up a strength class.
Proof Load & Strength for M16
| Tensile stress area As (ISO 724) | 157 mm² |
|---|---|
| Proof load, class 8.8 | 91 kN |
| Proof load, class 10.9 | 130 kN |
| Proof load, class 12.9 | 152 kN |
| Min. ultimate tensile load, class 8.8 | 125 kN |
Proof load = tensile stress area × the proof stress Sp of the class, per ISO 898-1 — Sp is a lower figure than the yield stress Rp0.2 and the two are not interchangeable. The stress area is computed from this size's own diameter and pitch, so a fine-pitch designation gives the fine-pitch figure. Design the joint so the working preload stays below the proof load of the class selected.
M16 Hex Bolt — GB/T 5783 / ISO 4017 (Series 010) Weight
A steel M16 hex bolt at the listed 100 mm length weighs approximately 197 g each — about 197 kg per 1,000 pieces. Stainless A2/A4 weighs roughly the same (density 7.9–8.0 g/cm³).
Actual weight varies slightly with head form, thread and finish; use this figure for freight estimation only.
Installation Tips for M16 Hex Bolt — GB/T 5783 / ISO 4017 (Series 010)
- Use a 6-point socket where access allows — 12-point sockets are more prone to rounding the corners on smaller sizes.
- On flanged or serrated variants, do NOT add a separate flat washer — the flange already spreads the load and the washer can defeat the locking serrations.
When to Step Up or Down from M16
When the joint preload approaches the proof load of M16 class 8.8, step up to M20 class 8.8 (or move to M16 class 10.9). When the joint is over-specified, M12 often saves weight and cost without losing the safety margin.
Custom manufacturing · Made to drawing
Need hex bolt in a size this table does not list?
This page covers M16 hex bolt. Thread size and pitch, length, property class, drive form, head geometry and head marking are all specifiable — the standard part is where it starts, not where it stops. Made by cold heading or hot forging.
Minimum order from 2,000 pieces; samples within 7 days of drawing approval.
