M16 Hex Bolts, Fine Pitch (ISO 8765) are specified by thread size, length and head dimensions. The M16 row from the standard is reproduced below, followed by the drill sizes, spanner size and torque values used when installing this size.
M16 Dimensional Row (ISO 8765)
| Size | Fine pitch (mm) | Width across flats s (mm) | Head height k (mm) | Stress area As (mmu00b2) | Common length range (mm) | Property class | Reference standard |
|---|---|---|---|---|---|---|---|
| M16 | 1.5 | 24.0 | 10.0 | 167.0 | 40~160 | 8.8 / 10.9 | ISO 8765 |
Spanner & Drive for M16 Hex Bolts, Fine Pitch
Drive geometry for M16 Hex Bolts, Fine Pitch is given by the row above; match the tool to the listed values.
Hole Sizes for M16
| Coarse-thread pitch (ISO 724) | 1.5 mm |
|---|---|
| Through-hole / clearance (ISO 273 medium) | 17.5 mm |
| Tapping drill, coarse thread | 14.5 mm |
Tightening Torque for M16
| Class 8.8 (dry, ~µ 0.125) | ≈ 223 Nm |
|---|---|
| Class 10.9 (dry, ~µ 0.125) | ≈ 327 Nm |
| Class 12.9 (dry, ~µ 0.125) | ≈ 383 Nm |
Indicative dry-joint values. Lubrication can lower the required torque by 15–25%. Always confirm against the joint design, especially when going up a strength class.
Proof Load & Strength for M16
| Tensile stress area As (ISO 724) | 167 mm² |
|---|---|
| Proof load, class 8.8 | 97 kN |
| Proof load, class 10.9 | 139 kN |
| Proof load, class 12.9 | 162 kN |
| Min. ultimate tensile load, class 8.8 | 134 kN |
Proof load = tensile stress area × the proof stress Sp of the class, per ISO 898-1 — Sp is a lower figure than the yield stress Rp0.2 and the two are not interchangeable. The stress area is computed from this size's own diameter and pitch, so a fine-pitch designation gives the fine-pitch figure. Design the joint so the working preload stays below the proof load of the class selected.
M16 Hex Bolts, Fine Pitch Weight
A steel M16 hex bolts, fine pitch at the listed 40,160 mm length weighs approximately 63,425 g each — about 63,425 kg per 1,000 pieces. Stainless A2/A4 weighs roughly the same (density 7.9–8.0 g/cm³).
Actual weight varies slightly with head form, thread and finish; use this figure for freight estimation only.
Mating Parts for M16
For M16, pair with a M16 hex nut (ISO 4032 / DIN 934) and, where used, a M16 flat washer (ISO 7089 / DIN 125A) under the head and under the nut.
When to Step Up or Down from M16
When the joint preload approaches the proof load of M16 class 8.8, step up to M20 class 8.8 (or move to M16 class 10.9). When the joint is over-specified, M12 often saves weight and cost without losing the safety margin.
Custom manufacturing · Made to drawing
Need hex bolts, fine pitch in a size this table does not list?
This page covers M16 hex bolts, fine pitch. Where the standard stops, the drawing takes over: fine pitches, left-hand threads, partial threading, and property classes above the catalogued grade where material and heat treatment allow. Made by cold heading or hot forging.
Minimum order from 2,000 pieces; samples within 7 days of drawing approval.








