M16 Sealing Screws with Bonded Washer are manufactured to DIN 933 with a coarse thread pitch of 2 mm. This page lists the controlling dimensions for the M16 size — head geometry, width across flats, matching spanner size — together with the clearance hole, tapping drill and tightening torque used at assembly.
M16 Dimensional Row (DIN 933)
| Thread size | Pitch (mm) | Across flats s (mm) | Head height k (mm) | Seal outer diameter (mm) | Seal thickness (mm) | Seal material | Common length range (mm) | Reference standard |
|---|---|---|---|---|---|---|---|---|
| M16 | 2.0 | 24 | 10.0 | 24 | 2.0 | NBR | 25~80 | DIN 933 + BS 4518 |
Spanner & Drive for M16 Sealing Screws with Bonded Washer
Drive geometry for M16 Sealing Screws with Bonded Washer is given by the row above; match the tool to the listed values.
Hole Sizes for M16
| Coarse-thread pitch (ISO 724) | 2 mm |
|---|---|
| Through-hole / clearance (ISO 273 medium) | 17.5 mm |
| Tapping drill, coarse thread | 14 mm |
Tightening Torque for M16
| Class 8.8 (dry, ~µ 0.125) | ≈ 209 Nm |
|---|---|
| Class 10.9 (dry, ~µ 0.125) | ≈ 306 Nm |
| Class 12.9 (dry, ~µ 0.125) | ≈ 358 Nm |
Indicative dry-joint values. Lubrication can lower the required torque by 15–25%. Always confirm against the joint design, especially when going up a strength class.
Proof Load & Strength for M16
| Tensile stress area As (ISO 724) | 157 mm² |
|---|---|
| Proof load, class 8.8 | 91 kN |
| Proof load, class 10.9 | 130 kN |
| Proof load, class 12.9 | 152 kN |
| Min. ultimate tensile load, class 8.8 | 125 kN |
Proof load = tensile stress area × the proof stress Sp of the class, per ISO 898-1 — Sp is a lower figure than the yield stress Rp0.2 and the two are not interchangeable. The stress area is computed from this size's own diameter and pitch, so a fine-pitch designation gives the fine-pitch figure. Design the joint so the working preload stays below the proof load of the class selected.
M16 Sealing Screws with Bonded Washer Weight
A steel M16 sealing screws with bonded washer at the listed 2,580 mm length weighs approximately 4,111 g each — about 4,111 kg per 1,000 pieces. Stainless A2/A4 weighs roughly the same (density 7.9–8.0 g/cm³).
Actual weight varies slightly with head form, thread and finish; use this figure for freight estimation only.
Mating Parts for M16
For M16, pair with a M16 hex nut (ISO 4032 / DIN 934) and, where used, a M16 flat washer (ISO 7089 / DIN 125A) under the head and under the nut.
When to Step Up or Down from M16
When the joint preload approaches the proof load of M16 class 8.8, step up to M20 class 8.8 (or move to M16 class 10.9). When the joint is over-specified, M12 often saves weight and cost without losing the safety margin.
Custom manufacturing · Made to drawing
Need sealing screws with bonded washer in a size this table does not list?
This page covers M16 sealing screws with bonded washer. Thread size and pitch, length, property class, drive form, head geometry and head marking are all specifiable — the standard part is where it starts, not where it stops. Made by cold heading or warm forging.
Minimum order from 2,000 pieces; samples within 7 days of drawing approval.
