Dimensional and assembly data for M2.5 Slotted Set Screws with Cup Point to ISO 7436. Includes head size and width across flats, clearance-hole and tapping-drill diameters, tightening torque per property class, and the sizes to step up or down to when the joint requires it.
M2.5 Dimensional Row (ISO 7436)
| Size | dz_min (mm) | dz_max (mm) | n_nom (mm) | n_min (mm) | n_max (mm) | t_min (mm) | t_max (mm) | Length range l (mm) | Reference standard |
|---|---|---|---|---|---|---|---|---|---|
| M2.5 | 0.95 | 1.2 | 0.4 | 0.46 | 0.6 | 0.72 | 0.95 | 3~12 | ISO 7436 |
Spanner & Drive for M2.5 Slotted Set Screws with Cup Point
The hex socket for M2.5 Slotted Set Screws with Cup Point is shown in the spec table — use the matching Allen / hex key (an ISO 2936 hex key set covers the full range). Ball-end keys are for reaching the screw, not for tightening it — finish on the plain end, and on production work use a torque-controlled driver.
Hole Sizes for M2.5
| Coarse-thread pitch (ISO 724) | 0.45 mm |
|---|---|
| Through-hole / clearance (ISO 273 medium) | 2.9 mm |
| Tapping drill, coarse thread | 2.05 mm |
Tightening Torque for M2.5
| Class 8.8 (dry, ~µ 0.125) | ≈ 0.7 Nm |
|---|---|
| Class 10.9 (dry, ~µ 0.125) | ≈ Nm |
| Class 12.9 (dry, ~µ 0.125) | ≈ 1.2 Nm |
Indicative dry-joint values. Lubrication can lower the required torque by 15–25%. Always confirm against the joint design, especially when going up a strength class.
Proof Load & Strength for M2.5
Set screws are rated to ISO 898-5 by hardness, because they work in compression against a shaft rather than in tension. ISO 898-1 excludes them, and a set screw has no head to preload against, so neither a property class nor a preload torque applies. Seating torque depends on the point form and the shaft material.
M2.5 Slotted Set Screws with Cup Point Weight
A steel M2.5 slotted set screws with cup point at the listed 312 mm length weighs approximately 12 g each — about 12 kg per 1,000 pieces. Stainless A2/A4 weighs roughly the same (density 7.9–8.0 g/cm³).
Actual weight varies slightly with head form, thread and finish; use this figure for freight estimation only.
Installation Tips for M2.5 Slotted Set Screws with Cup Point
- Use a quality Allen key fully seated in the socket — partial engagement is the most common cause of stripped sockets at this size.
- For countersunk and button-head variants, chamfer the through-hole to seat the head flush without preloading the head/shank fillet.
- At M2.5 the joint is sensitive to over-torque — use a torque-limiting driver and check the head doesn't bury into a softer counterpart.
Mating Parts for M2.5
For M2.5, pair with a M2.5 hex nut (ISO 4032 / DIN 934) and, where used, a M2.5 flat washer (ISO 7089 / DIN 125A) under the head and under the nut.
Custom manufacturing · Made to drawing
Need slotted set screws with cup point in a size this table does not list?
This page covers M2.5 slotted set screws with cup point. Material and finish are usually what drives a special — a grade the standard part is not stocked in, or a coating chosen against a salt-spray figure instead of a default. Made by cold heading or warm forging.
Minimum order from 2,000 pieces; samples within 7 days of drawing approval.
