This page covers M4 Conical Spring Washers (HV) to DIN 6796. M4 is the nominal bolt size; the dimensional row below is reproduced from the product table, followed by the tolerance, material and selection notes that apply to this size.
M4 Dimensional Row (DIN 6796)
Size
Inner diameter d1 (mm)
Outer diameter d2 (mm)
Thickness s (mm)
Height h max (mm)
Height h min (mm)
Reference standard
M4
4.3
9
1
1.3
1.12
DIN 6796
Common Applications for M4 Conical Spring Washers (HV)
M4 Conical Spring Washers (HV) are commonly specified for small electronics hardware and precision assemblies.
Mating Parts for M4
A M4 flat washer pairs with a M4 bolt/screw and matching M4 nut.
Technical Drawing
Customize the parameters below — every spec field is editable, and the drawing redraws to match the values you choose. Changing the size will snap the other fields to that size's standard values; you can then override any individual value.
Sends the selected values to the quote form below.
Request a Quote
The form below follows the current technical drawing configuration. Change the drawing values above and the request details update automatically.
Dimensions & Specifications (DIN 6796)
Size
Inner diameter d1 (mm)
Outer diameter d2 (mm)
Thickness s (mm)
Height h max (mm)
Height h min (mm)
Reference standard
M2
2.2
5
0.4
0.6
0.5
DIN 6796
M2.5
2.7
6
0.5
0.72
0.61
DIN 6796
M3
3.2
7
0.6
0.85
0.72
DIN 6796
M3.5
3.7
8
0.8
1.06
0.92
DIN 6796
M4
4.3
9
1
1.3
1.12
DIN 6796
M5
5.3
11
1.2
1.55
1.35
DIN 6796
M6
6.4
14
1.5
2
1.7
DIN 6796
M7
7.4
17
1.75
2.3
2
DIN 6796
M8
8.4
18
2
2.6
2.4
DIN 6796
M10
10.5
23
2.5
3.2
2.8
DIN 6796
M12
13
29
3
3.95
3.43
DIN 6796
M14
15
35
3.5
4.65
4.04
DIN 6796
M16
17
39
4
5.25
4.58
DIN 6796
M18
19
42
4.5
5.6
5.08
DIN 6796
M20
21
45
5
6.4
5.6
DIN 6796
M22
23
49
5.5
7.05
6.15
DIN 6796
M24
25
56
6
7.75
6.77
DIN 6796
M27
28
60
6.5
8.35
7.3
DIN 6796
M30
31
70
7
9.2
8
DIN 6796
Materials & Grades
Select a material class to see the grades we supply it in. Each designation is listed with its ISO/EN, AISI/SAE, JIS and GB equivalents.
Third-party video, selected automatically for this topic. It is not produced by Engineering Hardware and is not a specification source — use the tables on this page for dimensional data.
Inside the plant
Manufactured in our own plant
This part is cold-formed, threaded, heat-treated and finished in-house. The stages below are where its class and finish are actually decided.
01
Cold heading
Wire rod is drawn to size and cold-formed into blanks. Forming rather than cutting keeps the grain flow continuous around the head, which is where a bolt is most likely to fail.
Head dimensions and under-head radius checked at set-up and per shift.
02
Thread rolling
Threads are rolled between hardened dies rather than cut. Rolled threads are stronger in fatigue than cut threads and hold pitch and flank angle far more consistently across a batch.
Go / no-go ring gauges to ISO 965 tolerance class 6g.
03
Heat treatment
Quench-and-temper brings carbon and alloy steel to the property class ordered — 8.8, 10.9 or 12.9 — with the furnace charge tracked so a finished lot can be traced back to it.
Core hardness and tensile tested per lot to ISO 898-1.
04
Surface treatment
Zinc, zinc-nickel, hot-dip galvanizing, black oxide, phosphate and Dacromet, selected against the service environment rather than against the price list.
Coating thickness and neutral salt spray hours to ISO 9227.
Frequently Asked Questions
Is M4 Conical Spring Washers (HV) suitable for electronics and small mechanisms?
M4 Conical Spring Washers (HV) is in the micro range and is widely used in electronics, instrument enclosures and small precision mechanisms. Watch the over-torque margin — micro joints strip easily.
What's the typical proof load behavior of M4 class 8.8?
Micro-thread joints are sensitive to plastic deformation in the first turn under load — use a torque-limiting driver and check the bearing surface deformation on softer mating materials.
Which washer dimensions matter most for M4?
For a flat washer, the outside diameter (the bearing surface) and the thickness control how the load is spread under the head and how much elastic preload is preserved. The inside diameter must clear the bolt body but not be so large that the head bears mostly on the washer's outer rim.
What is the coarse-thread pitch of M4 for Conical Spring Washers (HV)?
For M4 the standard coarse pitch is 0.7 mm — this is the value used for Conical Spring Washers (HV).
How do I request a quotation?
Use the technical drawing on this page to pick the exact configuration, then submit it with the quote form. We respond within one business day.
Need a fastener quote or a spec sheet?Message our engineers on WhatsApp — send a drawing or DIN number and get pricing back fast.Start WhatsApp Chat →
This website uses only necessary and functional cookies to operate, secure, and improve basic website performance.
We do not use advertising cookies, Google Analytics, or cross-site tracking technologies.
Privacy Policy
