M5×0.8 is one of the standard coarse-thread sizes for bicycle disc brake rotor bolts under Trade series (bicycle rotor bolts). The sections below reproduce the dimensional row, list the matching tools and hole sizes, and summarize where this size is normally specified.
M5×0.8 Dimensional Row (Trade series (bicycle rotor bolts))
| Thread size | Length options (mm) | Drive | Head diameter (mm) | Head height (mm) | Tightening torque (N·m) | Use |
|---|
| M5×0.8 | 7.5 / 10 / 12 / 15 | T25 Torx | 9.3~9.5 | 3~3.2 | 2~4 | six-bolt rotor fixing |
Spanner & Drive for M5×0.8 Bicycle Disc Brake Rotor Bolts
Drive geometry for M5×0.8 Bicycle Disc Brake Rotor Bolts is given by the row above; match the tool to the listed values.
M5×0.8 Bicycle Disc Brake Rotor Bolts Weight
A steel M5×0.8 bicycle disc brake rotor bolts at the listed 7.5 mm length weighs approximately 119 g each — about 119 kg per 1,000 pieces. Stainless A2/A4 weighs roughly the same (density 7.9–8.0 g/cm³).
Actual weight varies slightly with head form, thread and finish; use this figure for freight estimation only.
Installation Tips for M5×0.8 Bicycle Disc Brake Rotor Bolts
- At M5×0.8 the stretch in the bolt becomes the controlling factor — for critical joints, use angle-controlled or stretch-controlled tightening instead of pure torque.
Mating Parts for M5×0.8
For M5×0.8, pair with a M5×0.8 hex nut (ISO 4032 / DIN 934) and, where used, a M5×0.8 flat washer (ISO 7089 / DIN 125A) under the head and under the nut.
Custom manufacturing · Made to drawing
Need bicycle disc brake rotor bolts in a size this table does not list?
This page covers M5×0.8 bicycle disc brake rotor bolts. Head form and drive can be specified to the assembly rather than to a standard: a larger bearing face, a security drive, or a socket sized for the tool already on the bench. Made by cold heading or hot forging.
Minimum order from 2,000 pieces; samples within 7 days of drawing approval.
Custom bolt manufacturingSend a drawing
Applications & Industries for M5×0.8 Bicycle Disc Brake Rotor Bolts
The sectors that buy Bicycle Disc Brake Rotor Bolts, and the duty each one buys them for.
Industries that specify Bicycle Disc Brake Rotor Bolts
-
Bike service
T25 drive and 2–4 N·m guidance support repeatable rotor replacement.
-
Mountain bikes
Button-head stainless or titanium options fit exposed rotor hardware.
-
Road bikes
Short lengths keep the fastener clear of the hub and rotor.
-
Bicycle assembly
M5 rotor bolts attach six-bolt brake rotors to the hub.
-
Food, pharma & cleanroom
Stainless assemblies that are washed down, where the finish matters as much as the strength.
-
Machine building & OEM
The default fastener on production equipment: covers, brackets, motor mounts and sub-assemblies tightened to a specified torque.
Typical applications
- using a T25 driver and the rotor instruction
- selecting 7.5–15 mm length by hub and rotor stack
- checking head diameter and height against the rotor recess
- fixing a six-bolt disc rotor with M5×0.8 hardware
- bolting brackets, motors and gearboxes to a frame
- assemblies that are dismantled for service and re-torqued
Service conditions to specify against
- Marine and coastal
- Available in A4 (316) stainless for chloride exposure — coastal structures, pool halls, water treatment and deck hardware, where A2 will eventually pit.
- High load
- Supplied in ISO 898-1 property classes, so the joint can be designed to a stated proof load and tightened to a calculated torque rather than by feel.
- Torque and preload
- The joint is designed around bolt tension, so lubrication, coating and the friction coefficient all change the torque figure — state them together.
Where to use something else
- Do not use a generic bolt or washer under a rotor head unless the hub and rotor system specifies it.
- Do not use a machine thread into unthreaded sheet or timber; use a tapping screw, rivet nut or insert made for that parent material.
Full application guide: where Bicycle Disc Brake Rotor Bolts are used, how to specify them, and the cases they are wrong for