ASME B18.2.3.1 specifies the dimensions and tolerances for 12-point flange screws. The full dimensional table is reproduced below, followed by the DIN, ISO and ASME parts that match or supersede it.
- Standard
- ASME B18.2.3.1
- Product
- 12-Point Flange Screws
- Governing standards
- ASME B18.2.3.11M
Equivalence between national standards is dimensional, not always metallurgical. Check the property class separately when substituting.
The table below lists the dimensions catalogued for 12-point flange screws under ASME B18.2.3.1. The scope of ASME B18.2.3.1 itself is not summarised here — where a figure matters, confirm it against the published document.
ASME B18.2.3.1 — Scope
The table below lists the dimensions catalogued for 12-point flange screws under ASME B18.2.3.1. The scope of ASME B18.2.3.1 itself is not summarised here — where a figure matters, confirm it against the published document.
Tolerance & Product Grades
Product grade is a concept from dimensional fastener standards and does not apply to ASME B18.2.3.1. Tolerances for this part are the limits shown against each dimension in the table.
Dimensions Specified by ASME B18.2.3.1
| Thread size | Pitch (mm) | Wrenching size across corners (mm) | Flange diameter dc (mm) | Head height k (mm) | Common length range (mm) | Property class | Reference standard |
|---|
| M6 | 1.0 | 9.0 | 13.0 | 5.4 | 16~60 | 10.9 / 12.9 | ASME B18.2.3.11M |
| M8 | 1.25 | 11.0 | 16.6 | 7.2 | 20~80 | 10.9 / 12.9 | ASME B18.2.3.11M |
| M10 | 1.5 | 13.0 | 20.5 | 9.0 | 25~100 | 10.9 / 12.9 | ASME B18.2.3.11M |
| M12 | 1.75 | 16.0 | 24.4 | 10.8 | 30~120 | 10.9 / 12.9 | ASME B18.2.3.11M |
| M14 | 2.0 | 18.0 | 28.0 | 12.6 | 35~140 | 10.9 / 12.9 | ASME B18.2.3.11M |
| M16 | 2.0 | 21.0 | 32.2 | 14.4 | 40~160 | 10.9 / 12.9 | ASME B18.2.3.11M |
| M20 | 2.5 | 27.0 | 40.0 | 18.0 | 50~200 | 10.9 / 12.9 | ASME B18.2.3.11M |
Companion Standards
A complete specification for 12-point flange screws normally cites several documents: one for the geometry, one for the material or mechanical properties, and one for the finish. ASME B18.2.3.1 is one of them, not all of them.
When to Specify ASME B18.2.3.1
ASME B18.2.3.1 is the inch-based reference; for metric programs choose the ISO equivalent instead.
Custom manufacturing · Made to drawing
Need a bolt to this standard in a non-standard size?
Parts built to ASME B18 2 3 1 are already in the catalog, so a special is usually a variation on existing tooling rather than a new design — which is what keeps the cost down. Made by cold heading or hot forging.
Minimum order from 2,000 pieces; samples within 7 days of drawing approval.
Custom bolt manufacturingSend a drawing
Applications & Industries
Where 12-Point Flange Screws are used, and what decides the specification in each case. Stocked from M6 to M20.
Industries that specify 12-Point Flange Screws
-
Engine & powertrain
Connecting-rod, main-bearing and flywheel bolts torqued in a confined recess.
-
Motorsport & performance
High-preload joints where a socket must enter at a shallow angle.
-
Hydraulic & press equipment
Cylinder heads and tie rods at class 12.9.
-
Machine building & OEM
The default fastener on production equipment: covers, brackets, motor mounts and sub-assemblies tightened to a specified torque.
-
Automotive & transport
Chassis, driveline and body fixings that see vibration and are assembled to a controlled preload.
-
Steel fabrication
Bolted connections in frames, enclosures, walkways and weldments, on the bench and on site.
Typical applications
- high-preload joints in a counterbore a hex socket cannot reach
- twelve engagement points give access every 30°, not every 60°
- integral flange replaces the washer under the head
- clamping two machined faces to a calculated preload
- bolting brackets, motors and gearboxes to a frame
- assemblies that are dismantled for service and re-torqued
Service conditions to specify against
- Marine and coastal
- Available in A4 (316) stainless for chloride exposure — coastal structures, pool halls, water treatment and deck hardware, where A2 will eventually pit.
- High load
- Supplied in ISO 898-1 property classes, so the joint can be designed to a stated proof load and tightened to a calculated torque rather than by feel.
- Torque and preload
- The joint is designed around bolt tension, so lubrication, coating and the friction coefficient all change the torque figure — state them together.
Where to use something else
- Do not use a machine thread into unthreaded sheet or timber; use a tapping screw, rivet nut or insert made for that parent material.
Full application guide: where 12-Point Flange Screws are used, how to specify them, and the cases they are wrong for