DIN 787 specifies the dimensions and tolerances for t-slot bolts (din 787). The full dimensional table is reproduced below, followed by the DIN, ISO and ASME parts that match or supersede it.
- Standard
- DIN 787
- Product
- T-Slot Bolts (DIN 787)
- Governing standards
- DIN 787
Equivalence between national standards is dimensional, not always metallurgical. Check the property class separately when substituting.
The table below lists the dimensions catalogued for t-slot bolts (din 787) under DIN 787. The scope of DIN 787 itself is not summarised here — where a figure matters, confirm it against the published document.
DIN 787 — Scope
The table below lists the dimensions catalogued for t-slot bolts (din 787) under DIN 787. The scope of DIN 787 itself is not summarised here — where a figure matters, confirm it against the published document.
Tolerance & Product Grades
Product grade is a concept from dimensional fastener standards and does not apply to DIN 787. Tolerances for this part are the limits shown against each dimension in the table.
Dimensions Specified by DIN 787
| Thread size | For slot width (mm) | T-head width (mm) | T-head height (mm) | Nominal diameter d (mm) | Common length range (mm) | Property class | Reference standard |
|---|
| M8 | 10 | 16 | 7 | 8 | 40~100 | 8.8 | DIN 787 |
| M10 | 12 | 18 | 9 | 10 | 50~125 | 8.8 | DIN 787 |
| M12 | 14 | 22 | 11 | 12 | 50~160 | 8.8 | DIN 787 |
| M16 | 18 | 28 | 14 | 16 | 63~200 | 8.8 | DIN 787 |
| M20 | 22 | 34 | 18 | 20 | 80~250 | 10.9 | DIN 787 |
| M24 | 28 | 43 | 22 | 24 | 100~315 | 10.9 | DIN 787 |
Companion Standards
A complete specification for t-slot bolts (din 787) normally cites several documents: one for the geometry, one for the material or mechanical properties, and one for the finish. DIN 787 is one of them, not all of them.
When to Specify DIN 787
DIN 787 is still widely used in European mechanical engineering and as a cross-reference on legacy drawings; its ISO equivalent is preferred for new designs.
Custom manufacturing · Made to drawing
Need a bolt to this standard in a non-standard size?
Parts built to DIN 787 are already in the catalog, so a special is usually a variation on existing tooling rather than a new design — which is what keeps the cost down. Made by cold heading or hot forging.
Minimum order from 2,000 pieces; samples within 7 days of drawing approval.
Custom bolt manufacturingSend a drawing
Applications & Industries
The sectors that buy T-Slot Bolts to DIN 787, and the duty each one buys them for. Stocked from M8 to M24.
Industries that specify T-Slot Bolts
-
Jig & fixture building
Repositionable clamping on slotted base plates.
-
Automation & framing
Fixings into machine-table and profile slots.
-
Machine shops
Clamping vises, fixtures and workpieces to a milling or drilling table.
-
Automotive & transport
Chassis, driveline and body fixings that see vibration and are assembled to a controlled preload.
-
Steel fabrication
Bolted connections in frames, enclosures, walkways and weldments, on the bench and on site.
-
Energy & infrastructure
Tower, pipework, switchgear and plant fixings specified for long service life and inspectable joints.
Typical applications
- clamp sets built from a stud, T-bolt, step block and flange nut
- ordered by the table slot width first, thread second
- clamping through a machine table T-slot
- bolting brackets, motors and gearboxes to a frame
- assemblies that are dismantled for service and re-torqued
- joints where the property class is stated on the drawing
Service conditions to specify against
- Marine and coastal
- Available in A4 (316) stainless for chloride exposure — coastal structures, pool halls, water treatment and deck hardware, where A2 will eventually pit.
- High load
- Supplied in ISO 898-1 property classes, so the joint can be designed to a stated proof load and tightened to a calculated torque rather than by feel.
- Torque and preload
- The joint is designed around bolt tension, so lubrication, coating and the friction coefficient all change the torque figure — state them together.
Where to use something else
- Do not use a machine thread into unthreaded sheet or timber; use a tapping screw, rivet nut or insert made for that parent material.
Full application guide: where T-Slot Bolts are used, how to specify them, and the cases they are wrong for