Specification summary of ISO 7040 as applied to nylon insert hex lock nut: the dimensions the standard controls, the full specified size range, and the equivalent DIN/ISO/ASME designations.
ISO 7040 — Scope
ISO 7040 is "Prevailing torque type hexagon regular nuts (with non-metallic insert)".
Material, property class, surface finish and packaging are governed by separate documents — ISO 898-1 and ISO 898-2 for mechanical property classes, ISO 4042 for electroplated finishes.
Tolerance & Product Grades
ISO 7040 does not divide nylon insert hex lock nut — gb/t 889 / iso 7040 (series 078) into product grades. Tolerances are given as limits on the individual dimensions in the table.
Where a general-tolerance class is cited on the drawing instead, it applies to the dimensions not otherwise toleranced.
Dimensions Specified by ISO 7040
| Size | Pitch (mm) | Width across flats s (mm) | Width across corners e (mm) | Total height m (mm) | Reference standard |
|---|---|---|---|---|---|
| M3 | 0.5 | 5.5 | 6.01 | 4.0 | ISO 7040 / DIN 985 |
| M4 | 0.7 | 7.0 | 7.66 | 5.0 | ISO 7040 / DIN 985 |
| M5 | 0.8 | 8.0 | 8.79 | 5.0 | ISO 7040 / DIN 985 |
| M6 | 1.0 | 10.0 | 11.05 | 6.0 | ISO 7040 / DIN 985 |
| M8 | 1.25 | 13.0 | 14.38 | 8.0 | ISO 7040 / DIN 985 |
| M10 | 1.5 | 16.0 | 17.77 | 10.0 | ISO 7040 / DIN 985 |
| M12 | 1.75 | 18.0 | 20.03 | 12.0 | ISO 7040 / DIN 985 |
| M14 | 2.0 | 21.0 | 23.36 | 14.0 | ISO 7040 / DIN 985 |
| M16 | 2.0 | 24.0 | 26.75 | 16.0 | ISO 7040 / DIN 985 |
| M18 | 2.5 | 27.0 | 30.14 | 18.0 | ISO 7040 / DIN 985 |
| M20 | 2.5 | 30.0 | 33.53 | 20.0 | ISO 7040 / DIN 985 |
| M24 | 3.0 | 36.0 | 39.98 | 22.0 | ISO 7040 / DIN 985 |
| M30 | 3.5 | 46.0 | 50.85 | 25.0 | ISO 7040 / DIN 985 |
| M36 | 4.0 | 55.0 | 60.79 | 29.0 | ISO 7040 / DIN 985 |
Equivalent Standards
Where direct equivalents exist (ISO ↔ DIN, ISO ↔ ASME), they are listed on the parent Nylon Insert Hex Lock Nut — GB/T 889 / ISO 7040 (Series 078) page.
Always confirm against the dimensions on this page, since some "equivalent" standards differ in tolerances and head geometry.
Companion Standards
ISO 7040 controls only the geometry of nylon insert hex lock nut — gb/t 889 / iso 7040 (series 078). The mechanical strength is set by ISO 898-1 (bolts, screws and studs) or ISO 898-2 (nuts); the surface finish is governed by separate finish standards such as ISO 4042 for electroplating. For corrosion testing, the relevant document is ISO 9227 (neutral salt spray).
Custom manufacturing · Made to drawing
Need a nut to this standard in a non-standard size?
Parts built to ISO 7040 are already in the catalog, so a special is usually a variation on existing tooling rather than a new design — which is what keeps the cost down. Made by cold heading or tapping.
Minimum order from 2,000 pieces; samples within 7 days of drawing approval.
