ISO 7050 is the governing dimensional standard for phillips countersunk self-tapping screw. This page sets out the scope of the standard, reproduces the full size table it specifies, and lists the DIN/ISO/ASME cross-references commonly cited in datasheets and drawings.
ISO 7050 — Scope
ISO 7050 specifies the dimensions and tolerances of phillips countersunk self-tapping screw — gb/t 846 / iso 7050 (series 028). Material, property class, surface finish and packaging are governed by separate documents in the same standards family (for example ISO 898-1 for the mechanical property classes of bolts and screws).
Tolerance & Product Grades
ISO 7050, alongside the related GB/T 846 / ISO 7050 entries on this site, specifies product grades (typically A or B for fine work and C for general engineering) and tolerance classes for the controlling dimensions. Choose the grade against the precision your application requires.
Dimensions Specified by ISO 7050
| Size | Pitch (mm) | Length L (mm) | Head diameter dk (mm) | Head height k (mm) | Cross recess | Countersink angle (deg) | Reference standard |
|---|---|---|---|---|---|---|---|
| M3 | 0.5 | 20 | 5.6 | 1.65 | PH1 | 90 | ISO 7046 / GB/T 819 |
| M4 | 0.7 | 25 | 7.5 | 2.2 | PH2 | 90 | ISO 7046 / GB/T 819 |
| M5 | 0.8 | 30 | 9.2 | 2.5 | PH2 | 90 | ISO 7046 / GB/T 819 |
| M6 | 1.0 | 40 | 11.0 | 3.0 | PH3 | 90 | ISO 7046 / GB/T 819 |
| M8 | 1.25 | 50 | 14.5 | 4.0 | PH3 | 90 | ISO 7046 / GB/T 819 |
| M10 | 1.5 | 60 | 18.0 | 5.0 | PH4 | 90 | ISO 7046 / GB/T 819 |
| M12 | 1.75 | 80 | 22.0 | 6.0 | PH4 | 90 | ISO 7046 / GB/T 819 |
| M14 | 2.0 | 80 | 25.0 | 7.0 | PH4 | 90 | ISO 7046 / GB/T 819 |
| M16 | 2.0 | 100 | 29.0 | 8.0 | PH4 | 90 | ISO 7046 / GB/T 819 |
| M18 | 2.5 | 100 | 33.0 | 9.0 | PH4 | 90 | ISO 7046 / GB/T 819 |
| M20 | 2.5 | 120 | 36.5 | 10.0 | PH4 | 90 | ISO 7046 / GB/T 819 |
| M24 | 3.0 | 150 | 43.5 | 12.0 | PH4 | 90 | ISO 7046 / GB/T 819 |
Equivalent Standards
Where direct equivalents exist (ISO ↔ DIN, ISO ↔ ASME), they are listed on the parent Phillips Countersunk Self-Tapping Screw — GB/T 846 / ISO 7050 (Series 028) page. Always confirm against the dimensions on this page, since some "equivalent" standards differ in tolerances and head geometry.
Companion Standards
ISO 7050 controls only the geometry of phillips countersunk self-tapping screw — gb/t 846 / iso 7050 (series 028). The mechanical strength is set by ISO 898-1 (bolts and screws) or ISO 898-2 (nuts); the surface finish is governed by separate finish standards (e.g. ISO 4042 for electroplating). For corrosion testing, the relevant document is ISO 9227 (neutral salt spray).