The table below lists the dimensions catalogued for hex nut, fine pitch under ISO 8673. The scope of ISO 8673 itself is not summarised here — where a figure matters, confirm it against the published document.
ISO 8673 — Scope
The table below lists the dimensions catalogued for hex nut, fine pitch — gb/t 6171 / iso 8673 (series 067) under ISO 8673. The scope of ISO 8673 itself is not summarised here — where a figure matters, confirm it against the published document.
Tolerance & Product Grades
Product grade is a concept from dimensional fastener standards and does not apply to ISO 8673. Tolerances for this part are the limits shown against each dimension in the table.
Dimensions Specified by ISO 8673
| Size | Pitch (mm) | Width across flats s (mm) | Width across corners e (mm) | Nut height m (mm) | Reference standard |
|---|---|---|---|---|---|
| M3 | 0.5 | 5.5 | 6.01 | 2.4 | ISO 4032 / GB/T 6170 |
| M4 | 0.7 | 7.0 | 7.66 | 3.2 | ISO 4032 / GB/T 6170 |
| M5 | 0.8 | 8.0 | 8.79 | 4.7 | ISO 4032 / GB/T 6170 |
| M6 | 1.0 | 10.0 | 11.05 | 5.2 | ISO 4032 / GB/T 6170 |
| M8 | 1.25 | 13.0 | 14.38 | 6.8 | ISO 4032 / GB/T 6170 |
| M10 | 1.5 | 16.0 | 17.77 | 8.4 | ISO 4032 / GB/T 6170 |
| M12 | 1.75 | 18.0 | 20.03 | 10.8 | ISO 4032 / GB/T 6170 |
| M14 | 2.0 | 21.0 | 23.36 | 12.8 | ISO 4032 / GB/T 6170 |
| M16 | 2.0 | 24.0 | 26.75 | 14.8 | ISO 4032 / GB/T 6170 |
| M18 | 2.5 | 27.0 | 30.14 | 15.8 | ISO 4032 / GB/T 6170 |
| M20 | 2.5 | 30.0 | 33.53 | 18.0 | ISO 4032 / GB/T 6170 |
| M24 | 3.0 | 36.0 | 39.98 | 21.5 | ISO 4032 / GB/T 6170 |
| M30 | 3.5 | 46.0 | 50.85 | 25.6 | ISO 4032 / GB/T 6170 |
| M36 | 4.0 | 55.0 | 60.79 | 31.0 | ISO 4032 / GB/T 6170 |
Equivalent Standards
Where direct equivalents exist (ISO ↔ DIN, ISO ↔ ASME), they are listed on the parent Hex Nut, Fine Pitch — GB/T 6171 / ISO 8673 (Series 067) page.
Always confirm against the dimensions on this page, since some "equivalent" standards differ in tolerances and head geometry.
When to Specify ISO 8673
Choose ISO 8673 for international engineering work and OEM supply where ISO standards are the contractual reference. It is the default modern specification for hex nut, fine pitch — gb/t 6171 / iso 8673 (series 067).
Custom manufacturing · Made to drawing
Need a nut to this standard in a non-standard size?
Parts built to ISO 8673 are already in the catalog, so a special is usually a variation on existing tooling rather than a new design — which is what keeps the cost down. Made by cold heading or tapping.
Minimum order from 2,000 pieces; samples within 7 days of drawing approval.
