SAE J429 specifies the dimensions and tolerances for square-head bolts. The full dimensional table is reproduced below, followed by the DIN, ISO and ASME parts that match or supersede it.
- Standard
- SAE J429
- Product
- Square-Head Bolts
- Governing standards
- ASME B18.2.1 / SAE J429 Grade 5
Equivalence between national standards is dimensional, not always metallurgical. Check the property class separately when substituting.
The table below lists the dimensions catalogued for square-head bolts under SAE J429. The scope of SAE J429 itself is not summarised here — where a figure matters, confirm it against the published document.
SAE J429 — Scope
The table below lists the dimensions catalogued for square-head bolts under SAE J429. The scope of SAE J429 itself is not summarised here — where a figure matters, confirm it against the published document.
Tolerance & Product Grades
Product grade is a concept from dimensional fastener standards and does not apply to SAE J429. Tolerances for this part are the limits shown against each dimension in the table.
Dimensions Specified by SAE J429
| Size | Thread form | Head width (in) | Head height (in) | Tensile strength (psi) | Material / grade | Reference standard |
|---|
| 1/4-20 | fully or partially threaded | 3/8 | 11/64 | 120000 | yellow-zinc-chromate steel, Grade 5 | ASME B18.2.1 / SAE J429 |
| M6 / M8 / M10 / M12 / M14 / M16 / M20 / M24 / M30 | fully or partially threaded | | | | yellow-zinc-chromate steel, Grade 5 | ASME B18.2.1 / SAE J429 |
| 5/16-18 through 1-1/4-7 | fully or partially threaded | | | | yellow-zinc-chromate steel, Grade 5 | ASME B18.2.1 / SAE J429 |
Companion Standards
A complete specification for square-head bolts normally cites several documents: one for the geometry, one for the material or mechanical properties, and one for the finish. SAE J429 is one of them, not all of them.
When to Specify SAE J429
Choose SAE J429 for international engineering work and OEM supply where ISO standards are the contractual reference. It is the default modern specification for square-head bolts.
Custom manufacturing · Made to drawing
Need a bolt to this standard in a non-standard size?
Parts built to SAE J429 are already in the catalog, so a special is usually a variation on existing tooling rather than a new design — which is what keeps the cost down. Made by cold heading or hot forging.
Minimum order from 2,000 pieces; samples within 7 days of drawing approval.
Custom bolt manufacturingSend a drawing
Applications & Industries
What Square-Head Bolts are specified for, industry by industry. Stocked from 1/4-20 to 5/16-18 through 1-1/4-7 (screw size).
Industries that specify Square-Head Bolts
-
Steel frames
Partial or full thread options fit different grip lengths.
-
Maintenance work
Metric and inch sizes cover mixed legacy equipment.
-
Fabricated machinery
Square heads provide wrench faces when a hex head is not desired.
-
Agricultural structures
Grade 5 steel covers general structural and equipment joints.
-
Machine building & OEM
The default fastener on production equipment: covers, brackets, motor mounts and sub-assemblies tightened to a specified torque.
-
Automotive & transport
Chassis, driveline and body fixings that see vibration and are assembled to a controlled preload.
Typical applications
- matching the Grade 5 material to the joint requirement
- using the stated ASME and SAE designations when ordering
- tightening a square head with an open wrench
- choosing full or partial thread from the grip
- assemblies that are dismantled for service and re-torqued
- joints where the property class is stated on the drawing
Service conditions to specify against
- Marine and coastal
- Available in A4 (316) stainless for chloride exposure — coastal structures, pool halls, water treatment and deck hardware, where A2 will eventually pit.
- High load
- Supplied in ISO 898-1 property classes, so the joint can be designed to a stated proof load and tightened to a calculated torque rather than by feel.
- Torque and preload
- The joint is designed around bolt tension, so lubrication, coating and the friction coefficient all change the torque figure — state them together.
Where to use something else
- Do not assume the square head provides the same wrench clearance as a standard hex head; check the actual envelope.
- Do not use a machine thread into unthreaded sheet or timber; use a tapping screw, rivet nut or insert made for that parent material.
Full application guide: where Square-Head Bolts are used, how to specify them, and the cases they are wrong for