T 5783 is the governing dimensional standard for hex head bolt, fully threaded. This page sets out the scope of the standard, reproduces the full size table it specifies, and lists the DIN/ISO/ASME cross-references commonly cited in datasheets and drawings.
T 5783 — Scope
T 5783 specifies the dimensions and tolerances of hex head bolt, fully threaded — gb/t 5783 / iso 4017 (series 012). Material, property class, surface finish and packaging are governed by separate documents in the same standards family (for example ISO 898-1 for the mechanical property classes of bolts and screws).
Tolerance & Product Grades
T 5783, alongside the related GB/T 5783 / ISO 4017 entries on this site, specifies product grades (typically A or B for fine work and C for general engineering) and tolerance classes for the controlling dimensions. Choose the grade against the precision your application requires.
Dimensions Specified by T 5783
| Size | Pitch (mm) | Nominal diameter d (mm) | Length L (mm) | Width across flats s (mm) | Width across corners e (mm) | Head height k (mm) |
|---|---|---|---|---|---|---|
| M3 | 0.5 | 3 | 20 | 5.5 | 6.01 | 2.0 |
| M4 | 0.7 | 4 | 25 | 7.0 | 7.66 | 2.8 |
| M5 | 0.8 | 5 | 30 | 8.0 | 8.79 | 3.5 |
| M6 | 1.0 | 6 | 40 | 10.0 | 11.05 | 4.0 |
| M8 | 1.25 | 8 | 50 | 13.0 | 14.38 | 5.3 |
| M10 | 1.5 | 10 | 60 | 16.0 | 17.77 | 6.4 |
| M12 | 1.75 | 12 | 80 | 18.0 | 20.03 | 7.5 |
| M14 | 2.0 | 14 | 80 | 21.0 | 23.36 | 8.8 |
| M16 | 2.0 | 16 | 100 | 24.0 | 26.75 | 10.0 |
| M18 | 2.5 | 18 | 100 | 27.0 | 30.14 | 11.5 |
| M20 | 2.5 | 20 | 120 | 30.0 | 33.53 | 12.5 |
| M24 | 3.0 | 24 | 150 | 36.0 | 39.98 | 15.0 |
| M30 | 3.5 | 30 | 180 | 46.0 | 50.85 | 18.7 |
| M36 | 4.0 | 36 | 200 | 55.0 | 60.79 | 22.5 |
Equivalent Standards
Where direct equivalents exist (ISO ↔ DIN, ISO ↔ ASME), they are listed on the parent Hex Head Bolt, Fully Threaded — GB/T 5783 / ISO 4017 (Series 012) page. Always confirm against the dimensions on this page, since some "equivalent" standards differ in tolerances and head geometry.
Companion Standards
T 5783 controls only the geometry of hex head bolt, fully threaded — gb/t 5783 / iso 4017 (series 012). The mechanical strength is set by ISO 898-1 (bolts and screws) or ISO 898-2 (nuts); the surface finish is governed by separate finish standards (e.g. ISO 4042 for electroplating). For corrosion testing, the relevant document is ISO 9227 (neutral salt spray).