2 catalogued sizes, dimensioned to Trade series (collated gas drive pins). Pick any row and the technical drawing redraws to it.
Gas Drive Pins to Trade series (collated gas drive pins): the full dimensional table is reproduced below. 2 sizes are held in the table below, and the technical drawing redraws to whichever row you select.
Standard
Trade series (collated gas drive pins)
Catalogued sizes
2
Dimensions are nominal values from the governing standard. Confirm the tolerance class for your application before ordering.
Gas Drive Pins — Trade series (collated gas drive pins)
Customize the parameters below — every spec field is editable, and the drawing redraws to match the values you choose. Changing the size will snap the other fields to that size's standard values; you can then override any individual value.
Sends the selected values to the quote form below.
Request a Quotation for Gas Drive Pins
The form below follows the current technical drawing configuration. Change the drawing values above and the request details update automatically.
Dimensions & Specifications (Trade series (collated gas drive pins))
Every row below is a starting point for the customizer above — pick any size and the drawing will redraw to that row.
Collation
Finish
Head configuration
Installation tool
Selection parameters
red plastic strip
electro-galvanized
plain head
gas-actuated nailer
pin length, shank diameter, substrate rating
red plastic strip
electro-galvanized
with washer
gas-actuated nailer
pin length, shank diameter, pull-out or shear requirement
Gas Drive Pins conform to Trade series (collated gas drive pins). As nails, they are specified by the dimensions in the table below; this page also covers materials, finishes and typical uses.
What Are Gas Drive Pins?
Gas Drive Pins are nails defined by Trade series (collated gas drive pins). They are selected by nominal diameter and the dimensional characteristics shown below, and are available in a range of materials and finishes to suit the application and environment.
Materials & Finishes
Common materials include carbon steel (typically zinc plated or hot-dip galvanized), hardened or case-hardened steel where wear matters, and stainless steel A2 (304) or A4 (316) for corrosion resistance. Specify the material, hardness where relevant, and the surface finish appropriate to your application and environment.
Goes With
Hardware commonly specified alongside Gas Drive Pins.
Pricing
Gas Drive Pins are supplied to order. Pricing starts from approximately US$0.030 per piece for standard sizes in carbon steel; final pricing depends on size, material, finish and order quantity (MOQ applies). Submit your exact configuration with the quote form above.
Gas Drive Pins — Trade series (collated gas drive pins)
This part is cold-formed, threaded, heat-treated and finished in-house. The stages below are where its class and finish are actually decided.
01
Cold heading
Wire rod is drawn to size and cold-formed into blanks. Forming rather than cutting keeps the grain flow continuous around the head, which is where a bolt is most likely to fail.
Head dimensions and under-head radius checked at set-up and per shift.
02
Thread rolling
Threads are rolled between hardened dies rather than cut. Rolled threads are stronger in fatigue than cut threads and hold pitch and flank angle far more consistently across a batch.
Go / no-go ring gauges to ISO 965 tolerance class 6g.
03
Heat treatment
Quench-and-temper brings carbon and alloy steel to the property class ordered — 8.8, 10.9 or 12.9 — with the furnace charge tracked so a finished lot can be traced back to it.
Core hardness and tensile tested per lot to ISO 898-1.
04
Surface treatment
Zinc, zinc-nickel, hot-dip galvanizing, black oxide, phosphate and Dacromet, selected against the service environment rather than against the price list.
Coating thickness and neutral salt spray hours to ISO 9227.
Frequently Asked Questions
What is the controlling standard for Gas Drive Pins?
Gas Drive Pins are manufactured to Trade series (collated gas drive pins). The dimensional values on this page follow that standard.
Which sizes of Gas Drive Pins does Engineering Hardware supply?
The table on this page lists 2 sizes for Gas Drive Pins, ranging from red plastic strip to red plastic strip. Sizes outside the table can be quoted on request.
In which materials are Gas Drive Pins supplied?
Gas Drive Pins are supplied in low-carbon and medium-carbon steel, with finishes including zinc plating, hot-dip galvanizing and black oxide. Choose material and finish to suit the load and the service environment for Gas Drive Pins.
How do I request a quotation?
Use the parametric drawing on this page to set the exact configuration (size, material, finish) and click "Request this configuration" — a specialist from Engineering Hardware will respond within one business day.
Need a fastener quote or a spec sheet?Message our engineers on WhatsApp — send a drawing or DIN number and get pricing back fast.Start WhatsApp Chat →
This website uses only necessary and functional cookies to operate, secure, and improve basic website performance.
We do not use advertising cookies, Google Analytics, or cross-site tracking technologies.
Privacy Policy
