A2 Stainless Steel Slotted Pan Head Screw are supplied to GB/T 67 / ISO 1580. The grade provides good general corrosion resistance and is largely non-magnetic; the practical service range is approx. -200 °C to +400 °C, subject to the property class and the joint. Property data, grade comparison and the full size table follow.
Why Choose A2 Stainless Steel for Slotted Pan Head Screw — GB/T 67 / ISO 1580 (Series 040)
The most common stainless group for indoor and general outdoor fasteners. For slotted pan head screw — gb/t 67 / iso 1580 (series 040), this matters when good general corrosion resistance is the primary requirement.
Mechanical & Physical Properties
| Grade designation | ISO 3506 group A2 (304 / 1.4301), commonly supplied A2-70 |
|---|---|
| Magnetic response | Largely non-magnetic |
| Service temperature | approx. -200 °C to +400 °C, subject to the property class and the joint |
| Corrosion characteristic | Good general corrosion resistance |
Corrosion Behavior in Service
A2 (304) gives excellent atmospheric and most-water corrosion resistance and is the most common stainless for Slotted Pan Head Screw — GB/T 67 / ISO 1580 (Series 040) in indoor and general outdoor service. In chloride-bearing environments (marine air, road salt, swimming pools) consider stepping up to A4 (316).
Galvanic & Galling Considerations
Two important notes for stainless slotted pan head screw — gb/t 67 / iso 1580 (series 040): (1) stainless can gall on stainless threads under load — use a thread lubricant or anti-galling compound, especially for M6 and below; (2) when joined to aluminum or galvanized steel, stainless can drive galvanic corrosion of the less-noble metal in wet service — isolate with a coating or sleeve where appropriate.
Using Stainless Fasteners in Aluminum
Stainless steel is more noble than aluminum, so in the presence of an electrolyte — rain, condensation, salt spray — the aluminum becomes the anode and corrodes at the joint. The effect is driven by the area ratio: a small stainless fastener in a large aluminum section is normally acceptable, while a large stainless fastener in thin aluminum is not. Where the joint is wet, isolate the two metals with a coated or nylon washer and a sealant, or specify an aluminum or coated fastener instead.
Sizes of Slotted Pan Head Screw — GB/T 67 / ISO 1580 (Series 040) Available in A2 Stainless Steel
| Size | Pitch (mm) | Length L (mm) | Head diameter dk (mm) | Head height k (mm) | Cross recess | Reference standard |
|---|---|---|---|---|---|---|
| M3 | 0.5 | 20 | 5.6 | 1.8 | PH1 | ISO 7045 / GB/T 818 |
| M4 | 0.7 | 25 | 8.0 | 2.4 | PH2 | ISO 7045 / GB/T 818 |
| M5 | 0.8 | 30 | 9.5 | 3.0 | PH2 | ISO 7045 / GB/T 818 |
| M6 | 1.0 | 40 | 12.0 | 3.6 | PH3 | ISO 7045 / GB/T 818 |
| M8 | 1.25 | 50 | 16.0 | 4.8 | PH3 | ISO 7045 / GB/T 818 |
| M10 | 1.5 | 60 | 20.0 | 6.0 | PH4 | ISO 7045 / GB/T 818 |
