For spiral-wound metal gasket in A2 Stainless Steel, the controlling selection factors are corrosion exposure, strength requirement and service temperature. The grade data for A2 Stainless Steel (ISO 3506 group A2 (304 / 1.4301), commonly supplied A2-70) is summarized below together with every size supplied.
Why Choose A2 Stainless Steel for Spiral-Wound Metal Gasket — GB/T 4622 / ASME B16.20 (Series 090)
The most common stainless group for indoor and general outdoor fasteners. For spiral-wound metal gasket — gb/t 4622 / asme b16.20 (series 090), this matters when good general corrosion resistance is the primary requirement.
Mechanical & Physical Properties
| Grade designation | ISO 3506 group A2 (304 / 1.4301), commonly supplied A2-70 |
|---|---|
| Magnetic response | Largely non-magnetic |
| Service temperature | approx. -200 °C to +400 °C, subject to the property class and the joint |
| Corrosion characteristic | Good general corrosion resistance |
Corrosion Behavior in Service
A2 (304) gives excellent atmospheric and most-water corrosion resistance and is the most common stainless for Spiral-Wound Metal Gasket — GB/T 4622 / ASME B16.20 (Series 090) in indoor and general outdoor service. In chloride-bearing environments (marine air, road salt, swimming pools) consider stepping up to A4 (316).
Galvanic & Galling Considerations
For stainless spiral-wound metal gasket — gb/t 4622 / asme b16.20 (series 090) the compatibility question is galvanic rather than galling: joined to aluminum or galvanized steel in wet service, stainless drives corrosion of the less-noble metal. Isolate with a coating, sleeve or non-conductive washer where the joint sees moisture. Note also that stainless is softer than hardened carbon steel, so where the part carries a wear or shear duty, check the load against the grade before substituting.
Using Stainless Fasteners in Aluminum
Expect the aluminum to corrode, not the fastener — stainless sits higher in the galvanic series, so the aluminum is the one that gives up material. A small fastener in a thick section spreads the loss over a large area and is usually fine; a large fastener in thin sheet concentrates it and is not. Keep water out of the joint, or isolate the two metals with a nylon or coated washer and a sealant.
Sizes of Spiral-Wound Metal Gasket — GB/T 4622 / ASME B16.20 (Series 090) Available in A2 Stainless Steel
| Nominal pipe size | Inner diameter d1 (mm) | Outer diameter d2 (mm) | Thickness t (mm) | Winding material | Reference standard |
|---|---|---|---|---|---|
| DN15 | 22 | 42 | 4.5 | 304SS + flexible graphite | GB/T 4622 / ASME B16.20 |
| DN20 | 27 | 49 | 4.5 | 304SS + flexible graphite | GB/T 4622 / ASME B16.20 |
| DN25 | 34 | 59 | 4.5 | 304SS + flexible graphite | GB/T 4622 / ASME B16.20 |
| DN32 | 43 | 69 | 4.5 | 304SS + flexible graphite | GB/T 4622 / ASME B16.20 |
| DN40 | 49 | 75 | 4.5 | 304SS + flexible graphite | GB/T 4622 / ASME B16.20 |
| DN50 | 61 | 87 | 4.5 | 304SS + flexible graphite | GB/T 4622 / ASME B16.20 |
| DN65 | 77 | 109 | 4.5 | 304SS + flexible graphite | GB/T 4622 / ASME B16.20 |
| DN80 | 89 | 121 | 4.5 | 304SS + flexible graphite | GB/T 4622 / ASME B16.20 |
| DN100 | 115 | 149 | 4.5 | 304SS + flexible graphite | GB/T 4622 / ASME B16.20 |
| DN150 | 169 | 205 | 4.5 | 304SS + flexible graphite | GB/T 4622 / ASME B16.20 |
Dimensions are independent of the material: every size above is available in A2 Stainless Steel.
Custom manufacturing · Made to drawing
Need this washer in a grade that is not listed?
A2 Stainless Steel is one of the grades the catalog describes. Bore, outside diameter, thickness, temper and finish are the variables here — there is no thread to specify, so the fit and the bearing area are what the drawing has to pin down. Made by stamping or punching.
Minimum order from 2,000 pieces; samples within 7 days of drawing approval.
