Material page for closed-end round-body blind rivet nuts in A2 Stainless Steel (ISO 3506 group A2 (304 / 1.4301), commonly supplied A2-70). The sizes below are the ones we supply; there is no published dimensional standard for this article, so the table rather than a standard number is what to quote. Corrosion behaviour is good general corrosion resistance and the service range is approx. -200 °C to +400 °C, subject to the property class and the joint.
Why Choose A2 Stainless Steel for Closed-End Round-Body Blind Rivet Nuts
The most common stainless group for indoor and general outdoor fasteners. For closed-end round-body blind rivet nuts, this matters when good general corrosion resistance is the primary requirement.
Mechanical & Physical Properties
| Grade designation | ISO 3506 group A2 (304 / 1.4301), commonly supplied A2-70 |
|---|---|
| Magnetic response | Largely non-magnetic |
| Service temperature | approx. -200 °C to +400 °C, subject to the property class and the joint |
| Corrosion characteristic | Good general corrosion resistance |
Corrosion Behavior in Service
A2 (304) gives excellent atmospheric and most-water corrosion resistance and is the most common stainless for Closed-End Round-Body Blind Rivet Nuts in indoor and general outdoor service. In chloride-bearing environments (marine air, road salt, swimming pools) consider stepping up to A4 (316).
Comparable Grades
For Closed-End Round-Body Blind Rivet Nuts, the alternative stainless grade is A4 (316). The practical dividing line is chlorides: A2 (304) is fine until salt is involved, and A4 (316) exists for the cases where it is — coastal, marine and road-salt service. Neither reaches the strength of a plated class 8.8 or 10.9 fastener.
Using Stainless Fasteners in Aluminum
The galvanic couple here runs the wrong way: aluminum is the less noble metal, so it corrodes and the fastener does not. What governs the rate is the ratio of areas — a large anode and a small cathode is a tolerable combination, the reverse concentrates the attack into thin material around the hole. An isolating washer plus sealant breaks the circuit; where that is impractical, match the fastener to the substrate.
Sizes of Closed-End Round-Body Blind Rivet Nuts Available in A2 Stainless Steel
| Thread size | Pitch (mm) | Grip range (mm) | Installation hole (mm) | Head diameter (mm) | End | Material options |
|---|---|---|---|---|---|---|
| M4 | 0.7 | 0.5~2.5 | 6.1 | 9.0 | closed | zinc-plated steel / stainless steel / aluminum alloy |
| M5 | 0.8 | 0.5~3.0 | 7.1 | 10.0 | closed | zinc-plated steel / stainless steel / aluminum alloy |
| M6 | 1.0 | 0.5~3.0 / 3.0~5.0 | 9.1 | 12.0 | closed | zinc-plated steel / stainless steel / aluminum alloy |
| M8 | 1.25 | 0.5~3.0 / 3.0~5.5 | 11.1 | 15.0 | closed | zinc-plated steel / stainless steel / aluminum alloy |
| M10 | 1.5 | 1.0~3.5 | 13.1 | 17.0 | closed | zinc-plated steel / stainless steel / aluminum alloy |
Dimensions are independent of the material: every size above is available in A2 Stainless Steel.
Custom manufacturing · Made to drawing
Need this nut in a grade that is not listed?
A2 Stainless Steel is one of the grades the catalog describes. Thread, height, across-flats, property class, locking feature and flange form can all be varied, including thread sizes the standard series does not run to. Made by cold heading or tapping.
Minimum order from 2,000 pieces; samples within 7 days of drawing approval.
