A2 Stainless Steel Soft-Tip Set Screws (Nylon and Brass) are supplied to our own published dimensions — this is a trade-series article rather than one covered by a dimensional standard, so confirm the figures against the part you are replacing. The grade provides good general corrosion resistance and is largely non-magnetic; the practical service range is approx. -200 °C to +400 °C, subject to the property class and the joint.
Why Choose A2 Stainless Steel for Soft-Tip Set Screws (Nylon and Brass)
The most common stainless group for indoor and general outdoor fasteners. For soft-tip set screws (nylon and brass), this matters when good general corrosion resistance is the primary requirement.
Mechanical & Physical Properties
| Grade designation | ISO 3506 group A2 (304 / 1.4301), commonly supplied A2-70 |
|---|---|
| Magnetic response | Largely non-magnetic |
| Service temperature | approx. -200 °C to +400 °C, subject to the property class and the joint |
| Corrosion characteristic | Good general corrosion resistance |
Galvanic & Galling Considerations
Two important notes for stainless soft-tip set screws (nylon and brass): (1) stainless can gall on stainless threads under load — use a thread lubricant or anti-galling compound, especially for M6 and below; (2) when joined to aluminum or galvanized steel, stainless can drive galvanic corrosion of the less-noble metal in wet service — isolate with a coating or sleeve where appropriate.
Comparable Grades
For Soft-Tip Set Screws (Nylon and Brass), the alternative stainless grade is A4 (316). The practical dividing line is chlorides: A2 (304) is fine until salt is involved, and A4 (316) exists for the cases where it is — coastal, marine and road-salt service. Neither reaches the strength of a plated class 8.8 or 10.9 fastener.
Using Stainless Fasteners in Aluminum
Stainless steel is more noble than aluminum, so with an electrolyte present — rain, condensation, salt spray — the aluminum becomes the anode and corrodes at the joint. Area ratio decides how bad it gets: a small stainless fastener in a large aluminum section is normally acceptable, a large stainless fastener in thin aluminum is not. Where the joint gets wet, isolate the metals with a coated or nylon washer and a sealant, or specify an aluminum or coated fastener instead.
Sizes of Soft-Tip Set Screws (Nylon and Brass) Available in A2 Stainless Steel
| Thread size | Tip length (mm) | Holding force vs steel point | Max temperature (°C) | Drive | Common length range (mm) | Marks the shaft |
|---|---|---|---|---|---|---|
| M4 | 2.0 | approx. 40% | 100 | Hex socket | 6~20 | No |
| M5 | 2.5 | approx. 40% | 100 | Hex socket | 6~25 | No |
| M6 | 3.0 | approx. 40% | 100 | Hex socket | 8~30 | No |
| M6 | 3.0 | approx. 70% | 250 | Hex socket | 8~30 | No |
| M8 | 4.0 | approx. 70% | 250 | Hex socket | 10~40 | No |
| M10 | 5.0 | approx. 70% | 250 | Hex socket | 12~50 | No |
Dimensions are independent of the material: the table above lists the sizes supplied, and on this page every one of them is quoted in A2 Stainless Steel. The catalogue's default material column has been omitted here so it cannot be read as contradicting that.
Custom manufacturing · Made to drawing
Need this screw in a grade that is not listed?
A2 Stainless Steel is one of the grades the catalog describes. Lengths and thread lengths outside the standard table are the commonest request, followed by a drive the standard does not offer and a head marked with your own part number. Made by cold heading or warm forging.
Minimum order from 2,000 pieces; samples within 7 days of drawing approval.







