A2 Stainless Steel Spring (Roll) Pins pairs the standard ISO 8748 / DIN 1481 with a A2 Stainless Steel base material. The sections below cover why engineers select this grade for spring (roll) pins, its corrosion and temperature behavior, and the sizes available.
Why Choose A2 Stainless Steel for Spring (Roll) Pins
The most common stainless grade for indoor and general outdoor fasteners. For spring (roll) pins, this matters when good general corrosion resistance is the primary requirement.
Mechanical & Physical Properties
| Grade designation | A2-70 (304) |
|---|---|
| Magnetic response | Largely non-magnetic |
| Service temperature | approx. -200 °C to +400 °C |
| Corrosion characteristic | Good general corrosion resistance |
Corrosion Behavior in Service
A2 (304) gives excellent atmospheric and most-water corrosion resistance and is the most common stainless for Spring (Roll) Pins in indoor and general outdoor service. In chloride-bearing environments (marine air, road salt, swimming pools) consider stepping up to A4 (316).
Galvanic & Galling Considerations
Two important notes for stainless spring (roll) pins: (1) stainless can gall on stainless threads under load — use a thread lubricant or anti-galling compound, especially for M6 and below; (2) when joined to aluminum or galvanized steel, stainless can drive galvanic corrosion of the less-noble metal in wet service — isolate with a coating or sleeve where appropriate.
Sizes of Spring (Roll) Pins Available in A2 Stainless Steel
| Nominal diameter (mm) | Recommended hole (mm) | Common length range (mm) | End chamfer (mm) | Material | Reference standard |
|---|---|---|---|---|---|
| 1.0 | 1.0 | 4~10 | 0.3 | Spring steel | ISO 8748 / DIN 1481 |
| 1.2 | 1.2 | 4~12 | 0.3 | Spring steel | ISO 8748 / DIN 1481 |
| 1.5 | 1.5 | 4~16 | 0.3 | Spring steel | ISO 8748 / DIN 1481 |
| 2.0 | 2.0 | 6~20 | 0.5 | Spring steel | ISO 8748 / DIN 1481 |
| 2.5 | 2.5 | 6~24 | 0.5 | Spring steel | ISO 8748 / DIN 1481 |
| 3.0 | 3.0 | 8~30 | 0.5 | Spring steel | ISO 8748 / DIN 1481 |
| 4.0 | 4.0 | 8~40 | 0.8 | Spring steel | ISO 8748 / DIN 1481 |
| 5.0 | 5.0 | 10~50 | 0.8 | Spring steel | ISO 8748 / DIN 1481 |
| 6.0 | 6.0 | 12~60 | 1.0 | Spring steel | ISO 8748 / DIN 1481 |
| 8.0 | 8.0 | 16~80 | 1.0 | Spring steel | ISO 8748 / DIN 1481 |
| 10.0 | 10.0 | 20~100 | 1.5 | Spring steel | ISO 8748 / DIN 1481 |
| 12.0 | 12.0 | 25~120 | 1.5 | Spring steel | ISO 8748 / DIN 1481 |
| 13.0 | 13.0 | 25~120 | 1.5 | Spring steel | ISO 8748 / DIN 1481 |
| 14.0 | 14.0 | 30~160 | 2.0 | Spring steel | ISO 8748 / DIN 1481 |
| 16.0 | 16.0 | 30~160 | 2.0 | Spring steel | ISO 8748 / DIN 1481 |
| 20.0 | 20.0 | 40~200 | 2.0 | Spring steel | ISO 8748 / DIN 1481 |