A4 Stainless Steel Clamping Handle Screw (Short) are supplied to DIN 6336 / GN 313. The grade provides superior, including marine and chloride environments and is largely non-magnetic; the practical service range is approx. -200 °C to +400 °C, subject to the property class and the joint. Property data, grade comparison and the full size table follow.
Why Choose A4 Stainless Steel for Clamping Handle Screw (Short) — DIN 6336 / GN 313 (Series 042)
Specified for marine, coastal and chemical applications. For clamping handle screw (short) — din 6336 / gn 313 (series 042), this matters when superior, including marine and chloride environments is the primary requirement.
Mechanical & Physical Properties
| Grade designation | ISO 3506 group A4 (316 / 1.4401), commonly supplied A4-80 |
|---|---|
| Magnetic response | Largely non-magnetic |
| Service temperature | approx. -200 °C to +400 °C, subject to the property class and the joint |
| Corrosion characteristic | Superior, including marine and chloride environments |
Corrosion Behavior in Service
A4 (316) adds 2–3% molybdenum to the A2 (304) composition, which dramatically improves resistance to chloride-pitting corrosion. For Clamping Handle Screw (Short) — DIN 6336 / GN 313 (Series 042) in marine, coastal, swimming-pool or food-processing environments, A4 is the default selection.
Galvanic & Galling Considerations
Two important notes for stainless clamping handle screw (short) — din 6336 / gn 313 (series 042): (1) stainless can gall on stainless threads under load — use a thread lubricant or anti-galling compound, especially for M6 and below; (2) when joined to aluminum or galvanized steel, stainless can drive galvanic corrosion of the less-noble metal in wet service — isolate with a coating or sleeve where appropriate.
Using Stainless Fasteners in Aluminum
Expect the aluminum to corrode, not the fastener — stainless sits higher in the galvanic series, so the aluminum is the one that gives up material. A small fastener in a thick section spreads the loss over a large area and is usually fine; a large fastener in thin sheet concentrates it and is not. Keep water out of the joint, or isolate the two metals with a nylon or coated washer and a sealant.
Sizes of Clamping Handle Screw (Short) — DIN 6336 / GN 313 (Series 042) Available in A4 Stainless Steel
| Thread size | Pitch (mm) | Length L (mm) | Handle length (mm) | Knob diameter (mm) | Reference standard |
|---|---|---|---|---|---|
| M5 | 0.8 | 20 | 45 | 28 | DIN 6336 / GN 313 |
| M6 | 1.0 | 25 | 50 | 32 | DIN 6336 / GN 313 |
| M8 | 1.25 | 30 | 60 | 40 | DIN 6336 / GN 313 |
| M10 | 1.5 | 40 | 70 | 45 | DIN 6336 / GN 313 |
| M12 | 1.75 | 50 | 80 | 50 | DIN 6336 / GN 313 |
Dimensions are independent of the material: every size above is available in A4 Stainless Steel.
Custom manufacturing · Made to drawing
Need this bolt in a grade that is not listed?
A4 Stainless Steel is one of the grades the catalog describes. Where the standard stops, the drawing takes over: fine pitches, left-hand threads, partial threading, and property classes above the catalogued grade where material and heat treatment allow. Made by cold heading or hot forging.
Minimum order from 2,000 pieces; samples within 7 days of drawing approval.
