A4 Stainless Steel (ISO 3506 group A4 (316 / 1.4401), commonly supplied A4-80) is specified for marine, coastal and chemical applications. Specified on flow-drilling screws it determines the corrosion behaviour (superior, including marine and chloride environments) and the service temperature range (approx. -200 °C to +400 °C, subject to the property class and the joint); the dimensions are ours rather than a standard's, and are listed in full below.
Why Choose A4 Stainless Steel for Flow-Drilling Screws
Specified for marine, coastal and chemical applications. For flow-drilling screws, this matters when superior, including marine and chloride environments is the primary requirement.
Mechanical & Physical Properties
| Grade designation | ISO 3506 group A4 (316 / 1.4401), commonly supplied A4-80 |
|---|---|
| Magnetic response | Largely non-magnetic |
| Service temperature | approx. -200 °C to +400 °C, subject to the property class and the joint |
| Corrosion characteristic | Superior, including marine and chloride environments |
Corrosion Behavior in Service
A4 (316) adds 2–3% molybdenum to the A2 (304) composition, which dramatically improves resistance to chloride-pitting corrosion. For Flow-Drilling Screws in marine, coastal, swimming-pool or food-processing environments, A4 is the default selection.
Galvanic & Galling Considerations
Two important notes for stainless flow-drilling screws: (1) stainless can gall on stainless threads under load — use a thread lubricant or anti-galling compound, especially for M6 and below; (2) when joined to aluminum or galvanized steel, stainless can drive galvanic corrosion of the less-noble metal in wet service — isolate with a coating or sleeve where appropriate.
Using Stainless Fasteners in Aluminum
Expect the aluminum to corrode, not the fastener — stainless sits higher in the galvanic series, so the aluminum is the one that gives up material. A small fastener in a thick section spreads the loss over a large area and is usually fine; a large fastener in thin sheet concentrates it and is not. Keep water out of the joint, or isolate the two metals with a nylon or coated washer and a sealant.
Sizes of Flow-Drilling Screws Available in A4 Stainless Steel
| Thread size | Clearance-hole diameter (mm) | Steel sheet range (mm) | Aluminum sheet range (mm) | Magnesium sheet range (mm) | Example drive / head |
|---|---|---|---|---|---|
| M3 | 3.6~4.0 | 0.3~1.8 | 0.8~5.0 | 0.8~3.5 | varies by series |
| M3.5 | 4.3~4.8 | 0.3~1.8 | 0.8~5.0 | 0.8~3.5 | varies by series |
| M4 | 5.1~5.7 | 0.3~1.8 | 0.8~5.0 | 0.8~3.5 | M4×20 stainless; PH2/PZ2/T25 examples |
| M5 | 6.7~7.4 | 0.3~1.8 | 0.8~5.0 | 0.8~3.5 | M5×20 stainless; PH2/PZ2/T25 examples |
| M6 | 8.2~9.1 | 0.3~1.8 | 0.8~5.0 | 0.8~3.5 | varies by series |
Dimensions are independent of the material: every size above is available in A4 Stainless Steel.
Custom manufacturing · Made to drawing
Need this screw in a grade that is not listed?
A4 Stainless Steel is one of the grades the catalog describes. Lengths and thread lengths outside the standard table are the commonest request, followed by a drive the standard does not offer and a head marked with your own part number. Made by cold heading or warm forging.
Minimum order from 2,000 pieces; samples within 7 days of drawing approval.








