A4 Stainless Steel JIS Cross-Recess Micro Screws are supplied to our own published dimensions — this is a trade-series article rather than one covered by a dimensional standard, so confirm the figures against the part you are replacing. The grade provides superior, including marine and chloride environments and is largely non-magnetic; the practical service range is approx. -200 °C to +400 °C, subject to the property class and the joint.
Why Choose A4 Stainless Steel for JIS Cross-Recess Micro Screws
Specified for marine, coastal and chemical applications. For jis cross-recess micro screws, this matters when superior, including marine and chloride environments is the primary requirement.
Mechanical & Physical Properties
| Grade designation | ISO 3506 group A4 (316 / 1.4401), commonly supplied A4-80 |
|---|---|
| Magnetic response | Largely non-magnetic |
| Service temperature | approx. -200 °C to +400 °C, subject to the property class and the joint |
| Corrosion characteristic | Superior, including marine and chloride environments |
Galvanic & Galling Considerations
Two important notes for stainless jis cross-recess micro screws: (1) stainless can gall on stainless threads under load — use a thread lubricant or anti-galling compound, especially for M6 and below; (2) when joined to aluminum or galvanized steel, stainless can drive galvanic corrosion of the less-noble metal in wet service — isolate with a coating or sleeve where appropriate.
Comparable Grades
For JIS Cross-Recess Micro Screws, the alternative stainless grade is A2 (304). The practical dividing line is chlorides: A2 (304) is fine until salt is involved, and A4 (316) exists for the cases where it is — coastal, marine and road-salt service. Neither reaches the strength of a plated class 8.8 or 10.9 fastener.
Using Stainless Fasteners in Aluminum
The galvanic couple here runs the wrong way: aluminum is the less noble metal, so it corrodes and the fastener does not. What governs the rate is the ratio of areas — a large anode and a small cathode is a tolerable combination, the reverse concentrates the attack into thin material around the hole. An isolating washer plus sealant breaks the circuit; where that is impractical, match the fastener to the substrate.
Sizes of JIS Cross-Recess Micro Screws Available in A4 Stainless Steel
| Thread size | Head diameter (mm) | Head height (mm) | Length options (mm) | Drive | Finish |
|---|---|---|---|---|---|
| M1.0 | 1.8 | 0.50 | 2.5 | JCIS/JIS #0–1 | trivalent zinc-plated steel |
| M1.2 | 1.8 | 0.50 | 2~5 | JCIS/JIS #0–1 | trivalent zinc-plated steel |
| M1.4 | 2.0 | 0.50 | 1.4~12 | JCIS/JIS #0–1 | trivalent zinc-plated steel |
| M1.6 | 2.3 | 0.50 | 1.5~12 | JCIS/JIS #0–1 | trivalent zinc-plated steel |
| M1.7 | 2.5 | 0.50 | 1.5~14 | JCIS/JIS #0–1 | trivalent zinc-plated steel |
Dimensions are independent of the material: every size above is available in A4 Stainless Steel.
Custom manufacturing · Made to drawing
Need this screw in a grade that is not listed?
A4 Stainless Steel is one of the grades the catalog describes. Head form and drive can be specified to the assembly rather than to a standard: a larger bearing face, a security drive, or a socket sized for the tool already on the bench. Made by cold heading or warm forging.
Minimum order from 2,000 pieces; samples within 7 days of drawing approval.







