Property Class 12.9 Steel JIS Cross-Recess Micro Screws are supplied to ISO 898-1 property class 12.9. Corrosion behaviour is requires plating or black-oxide protection, the material is magnetic, and the usable service range is commonly limited to approx. +300 °C; confirm against the coating and the load. In practice this grade is the highest common strength class, for high-load machine assembly.
- Grade
- ISO 898-1 property class 12.9
- Corrosion resistance
- Requires plating or black-oxide protection
- Magnetic response
- Magnetic
- Service temperature
- commonly limited to approx. +300 °C; confirm against the coating and the load
Property values are typical for the grade. Certified mechanical test data is available on request for production orders.
Property Class 12.9 Steel (ISO 898-1 property class 12.9) is the highest common strength class, for high-load machine assembly. Specified on jis cross-recess micro screws it determines the corrosion behaviour (requires plating or black-oxide protection) and the service temperature range (commonly limited to approx. +300 °C; confirm against the coating and the load); the dimensions are ours rather than a standard's, and are listed in full below.
Why Choose Property Class 12.9 Steel for JIS Cross-Recess Micro Screws
The highest common strength class, for high-load machine assembly. For jis cross-recess micro screws, this matters when requires plating or black-oxide protection is the primary requirement.
Mechanical & Physical Properties
| Grade designation | ISO 898-1 property class 12.9 |
|---|
| Magnetic response | Magnetic |
|---|
| Service temperature | commonly limited to approx. +300 °C; confirm against the coating and the load |
|---|
| Corrosion characteristic | Requires plating or black-oxide protection |
|---|
Corrosion Behavior in Service
Carbon and alloy steel jis cross-recess micro screws require a coating for corrosion protection. Zinc plating (with or without passivation) is the most common; hot-dip galvanizing is used for outdoor structural service; black-oxide is mainly a tarnish-prevention finish for tool-room use.
Galvanic & Galling Considerations
For jis cross-recess micro screws in steel, the dominant compatibility issue is hydrogen embrittlement at high property classes (10.9 and above) when electroplated. Plating must be followed by an appropriate baking treatment, or a non-electroplated finish (mechanical zinc, zinc flake) should be substituted.
Sizes of JIS Cross-Recess Micro Screws Available in Property Class 12.9 Steel
| Thread size | Head diameter (mm) | Head height (mm) | Length options (mm) | Drive | Finish |
|---|
| M1.0 | 1.8 | 0.50 | 2.5 | JCIS/JIS #0–1 | trivalent zinc-plated steel |
| M1.2 | 1.8 | 0.50 | 2~5 | JCIS/JIS #0–1 | trivalent zinc-plated steel |
| M1.4 | 2.0 | 0.50 | 1.4~12 | JCIS/JIS #0–1 | trivalent zinc-plated steel |
| M1.6 | 2.3 | 0.50 | 1.5~12 | JCIS/JIS #0–1 | trivalent zinc-plated steel |
| M1.7 | 2.5 | 0.50 | 1.5~14 | JCIS/JIS #0–1 | trivalent zinc-plated steel |
Dimensions are independent of the material: every size above is available in Property Class 12.9 Steel.
Custom manufacturing · Made to drawing
Need this screw in a grade that is not listed?
Grade 12 9 Steel is one of the grades the catalog describes. Thread size and pitch, length, property class, drive form, head geometry and head marking are all specifiable — the standard part is where it starts, not where it stops. Made by cold heading or warm forging.
Minimum order from 2,000 pieces; samples within 7 days of drawing approval.
Custom screw manufacturingSend a drawing
Applications & Industries
Where JIS Cross-Recess Micro Screws are used, and what decides the specification in each case. Stocked from M1.0 to M1.7.
Industries that specify JIS Cross-Recess Micro Screws
-
Consumer electronics
JIS cross recesses suit compact assemblies designed around Japanese service tooling.
-
Camera equipment
Short micro lengths secure covers and internal brackets.
-
Instrument repair
Trivalent zinc finishes support small replacement sets.
-
Precision production
Head height and length are selected for a confined enclosure.
-
Maintenance & MRO
Stocked replacements matched to an existing property class, thread and finish.
-
Food, pharma & cleanroom
Stainless assemblies that are washed down, where the finish matters as much as the strength.
Typical applications
- servicing a JCIS/JIS cross recess with the correct driver
- choosing the short length for the actual stack
- matching the small head to the surrounding component clearance
- keeping the trivalent finish consistent with the housing
- clamping two machined faces to a calculated preload
- bolting brackets, motors and gearboxes to a frame
Service conditions to specify against
- Marine and coastal
- Available in A4 (316) stainless for chloride exposure — coastal structures, pool halls, water treatment and deck hardware, where A2 will eventually pit.
- High load
- Supplied in ISO 898-1 property classes, so the joint can be designed to a stated proof load and tightened to a calculated torque rather than by feel.
- Torque and preload
- The joint is designed around bolt tension, so lubrication, coating and the friction coefficient all change the torque figure — state them together.
Where to use something else
- Do not treat a JCIS recess as an ordinary Phillips drive; the driver fit controls whether the small head survives service.
- Do not use a machine thread into unthreaded sheet or timber; use a tapping screw, rivet nut or insert made for that parent material.
Full application guide: where JIS Cross-Recess Micro Screws are used, how to specify them, and the cases they are wrong for