Material specification page for slotted adjusting screws (din 551) in A4 Stainless Steel. Covers the grade designation (ISO 3506 group A4 (316 / 1.4401), commonly supplied A4-80), corrosion and magnetic behavior, comparable grades and their trade-offs, and the sizes available to DIN 551.
Why Choose A4 Stainless Steel for Slotted Adjusting Screws (DIN 551)
Specified for marine, coastal and chemical applications. For slotted adjusting screws (din 551), this matters when superior, including marine and chloride environments is the primary requirement.
Mechanical & Physical Properties
| Grade designation | ISO 3506 group A4 (316 / 1.4401), commonly supplied A4-80 |
|---|---|
| Magnetic response | Largely non-magnetic |
| Service temperature | approx. -200 °C to +400 °C, subject to the property class and the joint |
| Corrosion characteristic | Superior, including marine and chloride environments |
Corrosion Behavior in Service
A4 (316) adds 2–3% molybdenum to the A2 (304) composition, which dramatically improves resistance to chloride-pitting corrosion. For Slotted Adjusting Screws (DIN 551) in marine, coastal, swimming-pool or food-processing environments, A4 is the default selection.
Comparable Grades
For Slotted Adjusting Screws (DIN 551), the alternative stainless grade is A2 (304). The practical dividing line is chlorides: A2 (304) is fine until salt is involved, and A4 (316) exists for the cases where it is — coastal, marine and road-salt service. Neither reaches the strength of a plated class 8.8 or 10.9 fastener.
Using Stainless Fasteners in Aluminum
Stainless steel is more noble than aluminum, so with an electrolyte present — rain, condensation, salt spray — the aluminum becomes the anode and corrodes at the joint. Area ratio decides how bad it gets: a small stainless fastener in a large aluminum section is normally acceptable, a large stainless fastener in thin aluminum is not. Where the joint gets wet, isolate the metals with a coated or nylon washer and a sealant, or specify an aluminum or coated fastener instead.
Sizes of Slotted Adjusting Screws (DIN 551) Available in A4 Stainless Steel
| Thread size | Pitch (mm) | Slot width n (mm) | Slot depth t (mm) | Point form | Common length range (mm) | Property class | Reference standard |
|---|---|---|---|---|---|---|---|
| M3 | 0.5 | 0.4 | 0.8 | Flat | 3~16 | 14H | DIN 551 |
| M4 | 0.7 | 0.6 | 1.1 | Flat | 4~20 | 14H | DIN 551 |
| M5 | 0.8 | 0.8 | 1.3 | Flat | 5~25 | 14H | DIN 551 |
| M6 | 1.0 | 1.0 | 1.5 | Flat | 6~30 | 14H | DIN 551 |
| M8 | 1.25 | 1.2 | 2.0 | Flat | 8~40 | 14H | DIN 551 |
| M10 | 1.5 | 1.6 | 2.5 | Flat | 10~50 | 14H | DIN 551 |
Dimensions are independent of the material: every size above is available in A4 Stainless Steel.
Custom manufacturing · Made to drawing
Need this screw in a grade that is not listed?
A4 Stainless Steel is one of the grades the catalog describes. Material and finish are usually what drives a special — a grade the standard part is not stocked in, or a coating chosen against a salt-spray figure instead of a default. Made by cold heading or warm forging.
Minimum order from 2,000 pieces; samples within 7 days of drawing approval.







