Material page for o-ring seal in FKM (Viton®-type) (fluoroelastomer, typically 75 Shore A). The sizes below are the ones we supply; there is no published dimensional standard for this article, so the table rather than a standard number is what to quote. Corrosion behaviour is excellent resistance to heat, fuels, and most chemicals; poor with ketones and hot water/steam and the service range is approx. -20 °C to +200 °C.
Why Choose FKM (Viton®-type) for O-Ring Seal — ISO / DIN (Series 160)
Specified where temperature or chemical exposure exceeds nitrile. For o-ring seal — iso / din (series 160), this matters when excellent resistance to heat, fuels, and most chemicals; poor with ketones and hot water/steam is the primary requirement.
Mechanical & Physical Properties
| Grade designation | fluoroelastomer, typically 75 Shore A |
|---|---|
| Magnetic response | Non-magnetic |
| Service temperature | approx. -20 °C to +200 °C |
| Corrosion characteristic | Excellent resistance to heat, fuels, and most chemicals; poor with ketones and hot water/steam |
Corrosion Behavior in Service
Carbon and alloy steel o-ring seal — iso / din (series 160) require a coating for corrosion protection. Zinc plating (with or without passivation) is the most common; hot-dip galvanizing is used for outdoor structural service; black-oxide is mainly a tarnish-prevention finish for tool-room use.
Comparable Grades
For o-ring seal — iso / din (series 160), consider NBR where the service is ordinary mineral oil and the cost matters, or EPDM for hot water and steam, which attacks FKM. Elastomer selection is decided by the medium, the temperature range and whether the seal is static or dynamic — not by strength.
Sizes of O-Ring Seal — ISO / DIN (Series 160) Available in FKM (Viton®-type)
| Inner diameter d1 (mm) | Outer diameter d2 (mm) | Wire dia (mm) | Working temp range | Reference standard |
|---|---|---|---|---|
| 5 | 9 | 2 | -30 to +110 C | ISO 3601 / GB/T 3452 |
| 8 | 12 | 2 | -30 to +110 C | ISO 3601 / GB/T 3452 |
| 10 | 16 | 3 | -30 to +110 C | ISO 3601 / GB/T 3452 |
| 15 | 21 | 3 | -30 to +110 C | ISO 3601 / GB/T 3452 |
| 20 | 26 | 3 | -30 to +110 C | ISO 3601 / GB/T 3452 |
| 25 | 33 | 4 | -30 to +110 C | ISO 3601 / GB/T 3452 |
| 30 | 38 | 4 | -30 to +110 C | ISO 3601 / GB/T 3452 |
| 40 | 50 | 5 | -30 to +110 C | ISO 3601 / GB/T 3452 |
| 50 | 60 | 5 | -30 to +110 C | ISO 3601 / GB/T 3452 |
| 60 | 72 | 6 | -30 to +110 C | ISO 3601 / GB/T 3452 |
| 80 | 92 | 6 | -30 to +110 C | ISO 3601 / GB/T 3452 |
| 100 | 114 | 7 | -30 to +110 C | ISO 3601 / GB/T 3452 |
Dimensions are independent of the material: the table above lists the sizes supplied, and on this page every one of them is quoted in FKM (Viton®-type). The catalogue's default material column has been omitted here so it cannot be read as contradicting that.
Custom manufacturing · Made to drawing
Need this seal in a grade that is not listed?
Fkm is one of the grades the catalog describes. A special seal is almost always a compound change rather than a size change — the same dimensions in a material that survives the medium.
Minimum order from 2,000 pieces; samples within 7 days of drawing approval.








