Silicone (VMQ) O-Ring Seal are supplied to our own published dimensions — this is a trade-series article rather than one covered by a dimensional standard, so confirm the figures against the part you are replacing. The grade provides inert and physiologically neutral; low tear and abrasion strength and is non-magnetic; the practical service range is approx. -60 °C to +200 °C.
Why Choose Silicone (VMQ) for O-Ring Seal — ISO / DIN (Series 160)
Used for wide temperature range and food/medical contact, in static seals only. For o-ring seal — iso / din (series 160), this matters when inert and physiologically neutral; low tear and abrasion strength is the primary requirement.
Mechanical & Physical Properties
| Grade designation | vinyl-methyl silicone, typically 70 Shore A |
|---|---|
| Magnetic response | Non-magnetic |
| Service temperature | approx. -60 °C to +200 °C |
| Corrosion characteristic | Inert and physiologically neutral; low tear and abrasion strength |
Galvanic & Galling Considerations
Galvanic and galling behavior do not apply to o-ring seal — iso / din (series 160) in Silicone (VMQ) — the relevant compatibility questions are chemical: confirm the elastomer against the fluid, the temperature and any cleaning agents in service, and check the gland or groove dimensions give the intended compression on the section.
Comparable Grades
For o-ring seal — iso / din (series 160), consider NBR or FKM wherever the seal is dynamic — silicone has low tear and abrasion strength and is a static-seal material. Elastomer selection is decided by the medium, the temperature range and whether the seal is static or dynamic — not by strength.
Sizes of O-Ring Seal — ISO / DIN (Series 160) Available in Silicone (VMQ)
| Inner diameter d1 (mm) | Outer diameter d2 (mm) | Wire dia (mm) | Working temp range | Reference standard |
|---|---|---|---|---|
| 5 | 9 | 2 | -30 to +110 C | ISO 3601 / GB/T 3452 |
| 8 | 12 | 2 | -30 to +110 C | ISO 3601 / GB/T 3452 |
| 10 | 16 | 3 | -30 to +110 C | ISO 3601 / GB/T 3452 |
| 15 | 21 | 3 | -30 to +110 C | ISO 3601 / GB/T 3452 |
| 20 | 26 | 3 | -30 to +110 C | ISO 3601 / GB/T 3452 |
| 25 | 33 | 4 | -30 to +110 C | ISO 3601 / GB/T 3452 |
| 30 | 38 | 4 | -30 to +110 C | ISO 3601 / GB/T 3452 |
| 40 | 50 | 5 | -30 to +110 C | ISO 3601 / GB/T 3452 |
| 50 | 60 | 5 | -30 to +110 C | ISO 3601 / GB/T 3452 |
| 60 | 72 | 6 | -30 to +110 C | ISO 3601 / GB/T 3452 |
| 80 | 92 | 6 | -30 to +110 C | ISO 3601 / GB/T 3452 |
| 100 | 114 | 7 | -30 to +110 C | ISO 3601 / GB/T 3452 |
Dimensions are independent of the material: the table above lists the sizes supplied, and on this page every one of them is quoted in Silicone (VMQ). The catalogue's default material column has been omitted here so it cannot be read as contradicting that.
Custom manufacturing · Made to drawing
Need this seal in a grade that is not listed?
Silicone is one of the grades the catalog describes. Inside diameter, cross-section and compound are the three that matter, and the compound is chosen against the fluid and the temperature rather than the dimensions.
Minimum order from 2,000 pieces; samples within 7 days of drawing approval.








