Property Class 12.9 Steel Drilled-Head Capstan Sealing Screws are supplied to ISO 898-1 property class 12.9. Corrosion behaviour is requires plating or black-oxide protection, the material is magnetic, and the usable service range is commonly limited to approx. +300 °C; confirm against the coating and the load. In practice this grade is the highest common strength class, for high-load machine assembly.
- Grade
- ISO 898-1 property class 12.9
- Corrosion resistance
- Requires plating or black-oxide protection
- Magnetic response
- Magnetic
- Service temperature
- commonly limited to approx. +300 °C; confirm against the coating and the load
Property values are typical for the grade. Certified mechanical test data is available on request for production orders.
Material specification page for drilled-head capstan sealing screws in Property Class 12.9 Steel. Covers the grade designation (ISO 898-1 property class 12.9), corrosion and magnetic behavior, comparable grades and their trade-offs, and the sizes available to GB/T 70.1 / DIN 912 / ISO 4762 and GB/T 70.3 / DIN 7991 / ISO 10642.
Why Choose Property Class 12.9 Steel for Drilled-Head Capstan Sealing Screws
The highest common strength class, for high-load machine assembly. For drilled-head capstan sealing screws, this matters when requires plating or black-oxide protection is the primary requirement.
Mechanical & Physical Properties
| Grade designation | ISO 898-1 property class 12.9 |
|---|
| Magnetic response | Magnetic |
|---|
| Service temperature | commonly limited to approx. +300 °C; confirm against the coating and the load |
|---|
| Corrosion characteristic | Requires plating or black-oxide protection |
|---|
Corrosion Behavior in Service
Carbon and alloy steel drilled-head capstan sealing screws require a coating for corrosion protection. Zinc plating (with or without passivation) is the most common; hot-dip galvanizing is used for outdoor structural service; black-oxide is mainly a tarnish-prevention finish for tool-room use.
Comparable Grades
For Drilled-Head Capstan Sealing Screws, class 8.8 is the comparable strength step. Move up when the joint preload approaches the proof load of the current class; move down when the joint is over-specified. For corrosion-critical service, switch to stainless A2 or A4.
Sizes of Drilled-Head Capstan Sealing Screws Available in Property Class 12.9 Steel
| Head form | Governing standards | Sealing feature | Property class | Finish |
|---|
| hexagon socket head cap | GB/T 70.1-2008 / DIN 912 / ISO 4762 | cross-drilled head for sealing wire | 8.8 | black oxide |
| countersunk hexagon socket | GB/T 70.3-2008 / DIN 7991 / ISO 10642 | cross-drilled head for sealing wire | 8.8 | black oxide |
Dimensions are independent of the material: every size above is available in Property Class 12.9 Steel.
Custom manufacturing · Made to drawing
Need this screw in a grade that is not listed?
Grade 12 9 Steel is one of the grades the catalog describes. Material and finish are usually what drives a special — a grade the standard part is not stocked in, or a coating chosen against a salt-spray figure instead of a default. Made by cold heading or warm forging.
Minimum order from 2,000 pieces; samples within 7 days of drawing approval.
Custom screw manufacturingSend a drawing
Applications & Industries
Drilled-Head Capstan Sealing Screws are bought for a small number of well-defined jobs. These are the ones we ship them for. Stocked from hexagon socket head cap to countersunk hexagon socket (nominal diameter).
Industries that specify Drilled-Head Capstan Sealing Screws
-
Regulated installations
Evidence of an unbroken seal on inspection.
-
Utility metering
A cross-drilled head takes a sealing wire that shows tampering.
-
Instrument enclosures
Closure control on calibrated equipment.
-
Test and measurement
Sealed access for certified instruments.
-
Food, pharma & cleanroom
Stainless assemblies that are washed down, where the finish matters as much as the strength.
-
Machine building & OEM
The default fastener on production equipment: covers, brackets, motor mounts and sub-assemblies tightened to a specified torque.
Typical applications
- recording the seal number against the installation
- threading a sealing wire through the drilled head and crimping it
- choosing the cap or countersunk form for the enclosure detail
- specifying class 8.8 black oxide as listed
- joints where the property class is stated on the drawing
- clamping two machined faces to a calculated preload
Service conditions to specify against
- Marine and coastal
- Available in A4 (316) stainless for chloride exposure — coastal structures, pool halls, water treatment and deck hardware, where A2 will eventually pit.
- High load
- Supplied in ISO 898-1 property classes, so the joint can be designed to a stated proof load and tightened to a calculated torque rather than by feel.
- Sealed joints
- Used where the fixing has to keep water or air out as well as hold — the elastomer, not the fastener, decides service life.
- Torque and preload
- The joint is designed around bolt tension, so lubrication, coating and the friction coefficient all change the torque figure — state them together.
Where to use something else
- Do not fit a sealing screw without actually closing the wire; an undrawn seal proves nothing.
- Do not use a machine thread into unthreaded sheet or timber; use a tapping screw, rivet nut or insert made for that parent material.
Full application guide: where Drilled-Head Capstan Sealing Screws are used, how to specify them, and the cases they are wrong for