Property Class 8.8 Steel (ISO 898-1 property class 8.8) is the workhorse medium-carbon alloy class for structural joints. When hex socket flat point set screw are specified in this grade, the dimensions remain per GB/T 77 / ISO 4026; the material determines corrosion behavior (requires plating (zinc) for corrosion protection) and the service temperature range (commonly limited to approx. +300 °C; confirm against the coating and the load). Both are covered below with the size table.
Why Choose Property Class 8.8 Steel for Hex Socket Flat Point Set Screw — GB/T 77 / ISO 4026 (Series 019)
The workhorse medium-carbon alloy class for structural joints. For hex socket flat point set screw — gb/t 77 / iso 4026 (series 019), this matters when requires plating (zinc) for corrosion protection is the primary requirement.
Mechanical & Physical Properties
| Grade designation | ISO 898-1 property class 8.8 |
|---|---|
| Magnetic response | Magnetic |
| Service temperature | commonly limited to approx. +300 °C; confirm against the coating and the load |
| Corrosion characteristic | Requires plating (zinc) for corrosion protection |
Galvanic & Galling Considerations
For hex socket flat point set screw — gb/t 77 / iso 4026 (series 019) in steel, the dominant compatibility issue is hydrogen embrittlement at high property classes (10.9 and above) when electroplated. Plating must be followed by an appropriate baking treatment, or a non-electroplated finish (mechanical zinc, zinc flake) should be substituted.
Comparable Grades
For Hex Socket Flat Point Set Screw — GB/T 77 / ISO 4026 (Series 019), class 10.9 or 12.9 is the comparable strength step. Move up when the joint preload approaches the proof load of the current class; move down when the joint is over-specified. For corrosion-critical service, switch to stainless A2 or A4.
Sizes of Hex Socket Flat Point Set Screw — GB/T 77 / ISO 4026 (Series 019) Available in Property Class 8.8 Steel
| Size | Pitch (mm) | Length L (mm) | Hex socket s (mm) | Engagement depth t min (mm) | Point diameter dp (mm) | Reference standard |
|---|---|---|---|---|---|---|
| M3 | 0.5 | 6 | 1.5 | 1.4 | 2.0 | ISO 4026-4029 / GB/T 77-79 |
| M4 | 0.7 | 6 | 2.0 | 2.0 | 2.5 | ISO 4026-4029 / GB/T 77-79 |
| M5 | 0.8 | 7 | 2.5 | 2.5 | 3.5 | ISO 4026-4029 / GB/T 77-79 |
| M6 | 1.0 | 9 | 3.0 | 3.0 | 4.0 | ISO 4026-4029 / GB/T 77-79 |
| M8 | 1.25 | 12 | 4.0 | 4.0 | 5.5 | ISO 4026-4029 / GB/T 77-79 |
| M10 | 1.5 | 15 | 5.0 | 5.0 | 7.0 | ISO 4026-4029 / GB/T 77-79 |
| M12 | 1.75 | 18 | 6.0 | 6.0 | 8.5 | ISO 4026-4029 / GB/T 77-79 |
| M16 | 2.0 | 24 | 8.0 | 8.0 | 12.0 | ISO 4026-4029 / GB/T 77-79 |
| M20 | 2.5 | 30 | 10.0 | 10.0 | 15.0 | ISO 4026-4029 / GB/T 77-79 |
| M24 | 3.0 | 36 | 12.0 | 12.0 | 18.0 | ISO 4026-4029 / GB/T 77-79 |
