Grade 8.8 Steel (class 8.8) is the workhorse medium-carbon alloy grade for structural joints. When t-slot nuts are specified in this grade, the dimensions remain per DIN 508; the material determines corrosion behavior (requires plating (zinc) for corrosion protection) and the service temperature range (up to approx. +300 °C). Both are covered below with the size table.
Why Choose Grade 8.8 Steel for T-Slot Nuts
The workhorse medium-carbon alloy grade for structural joints. For t-slot nuts, this matters when requires plating (zinc) for corrosion protection is the primary requirement.
Mechanical & Physical Properties
| Grade designation | class 8.8 |
|---|---|
| Magnetic response | Magnetic |
| Service temperature | up to approx. +300 °C |
| Corrosion characteristic | Requires plating (zinc) for corrosion protection |
Galvanic & Galling Considerations
For t-slot nuts in steel, the dominant compatibility issue is hydrogen embrittlement at high property classes (10.9 and above) when electroplated. Plating must be followed by an appropriate baking treatment, or a non-electroplated finish (mechanical zinc, zinc flake) should be substituted.
Comparable Grades
For T-Slot Nuts, class 10.9 or 12.9 is the comparable strength step. Move up when the joint preload approaches the proof load of the current class; move down when the joint is over-specified. For corrosion-critical service, switch to stainless A2 or A4.
Sizes of T-Slot Nuts Available in Grade 8.8 Steel
| Thread size | T-slot width (mm) | Nut width b (mm) | Total height h (mm) | Key height h1 (mm) | Hook width e (mm) | Reference standard |
|---|---|---|---|---|---|---|
| M5 | 6 | 8.0 | 8.0 | 4.5 | 6.4 | DIN 508 / GN505 |
| M6 | 8 | 10.0 | 10.0 | 5.5 | 8.4 | DIN 508 / GN505 |
| M8 | 10 | 12.0 | 12.0 | 7.0 | 10.4 | DIN 508 / GN505 |
| M8 | 12 | 14.0 | 12.0 | 7.0 | 12.4 | DIN 508 / GN505 |
| M10 | 12 | 14.0 | 14.0 | 8.0 | 12.4 | DIN 508 / GN505 |
| M10 | 14 | 16.0 | 14.0 | 8.0 | 14.4 | DIN 508 / GN505 |
| M12 | 14 | 16.0 | 17.0 | 10.0 | 14.4 | DIN 508 / GN505 |
| M12 | 18 | 20.0 | 17.0 | 10.0 | 18.4 | DIN 508 / GN505 |
| M16 | 18 | 20.0 | 20.0 | 12.0 | 18.4 | DIN 508 / GN505 |
| M16 | 22 | 25.0 | 20.0 | 12.0 | 22.4 | DIN 508 / GN505 |
| M20 | 22 | 25.0 | 25.0 | 15.0 | 22.4 | DIN 508 / GN505 |
| M20 | 28 | 32.0 | 25.0 | 15.0 | 28.4 | DIN 508 / GN505 |
| M24 | 28 | 32.0 | 30.0 | 18.0 | 28.4 | DIN 508 / GN505 |