The M12 size of Torx Countersunk Head Screw is dimensioned by GB/T 2673 / ISO 14583. The tables below give the dimensional row from the standard, the drill and spanner sizes that go with it, and the assembly torque per property class. The technical drawing on this page redraws to the exact values selected.
M12 Dimensional Row (GB/T 2673 / ISO 14583)
| Size | Pitch (mm) | Length L (mm) | Head diameter dk (mm) | Head height k (mm) | Cross recess | Countersink angle (deg) | Reference standard |
|---|---|---|---|---|---|---|---|
| M12 | 1.75 | 80 | 22.0 | 6.0 | PH4 | 90 | ISO 7046 / GB/T 819 |
Spanner & Drive for M12 Torx Countersunk Head Screw — GB/T 2673 / ISO 14583 (Series 023)
The hex socket for M12 Torx Countersunk Head Screw — GB/T 2673 / ISO 14583 (Series 023) is shown in the spec table — use the matching Allen / hex key (an ISO 2936 hex key set covers the full range). A T-handle key gives the most feel when you are judging preload by hand; anything repeated across a batch wants a torque-controlled driver instead.
Hole Sizes for M12
| Coarse-thread pitch (ISO 724) | 1.75 mm |
|---|---|
| Through-hole / clearance (ISO 273 medium) | 13.5 mm |
| Tapping drill, coarse thread | 10.25 mm |
Tightening Torque for M12
| Class 8.8 (dry, ~µ 0.125) | ≈ 84 Nm |
|---|---|
| Class 10.9 (dry, ~µ 0.125) | ≈ 124 Nm |
| Class 12.9 (dry, ~µ 0.125) | ≈ 145 Nm |
Indicative dry-joint values. Lubrication can lower the required torque by 15–25%. Always confirm against the joint design, especially when going up a strength class.
Proof Load & Strength for M12
| Tensile stress area As (ISO 724) | 84.3 mm² |
|---|---|
| Proof load, class 8.8 | 49 kN |
| Proof load, class 10.9 | 70 kN |
| Proof load, class 12.9 | 82 kN |
| Min. ultimate tensile load, class 8.8 | 67 kN |
Proof load = tensile stress area × the proof stress Sp of the class, per ISO 898-1 — Sp is a lower figure than the yield stress Rp0.2 and the two are not interchangeable. The stress area is computed from this size's own diameter and pitch, so a fine-pitch designation gives the fine-pitch figure. Design the joint so the working preload stays below the proof load of the class selected.
M12 Torx Countersunk Head Screw — GB/T 2673 / ISO 14583 (Series 023) Weight
A steel M12 torx countersunk head screw at the listed 80 mm length weighs approximately 239 g each — about 239 kg per 1,000 pieces. Stainless A2/A4 weighs roughly the same (density 7.9–8.0 g/cm³).
Actual weight varies slightly with head form, thread and finish; use this figure for freight estimation only.
Installation Tips for M12 Torx Countersunk Head Screw — GB/T 2673 / ISO 14583 (Series 023)
- Use a quality Allen key fully seated in the socket — partial engagement is the most common cause of stripped sockets at this size.
- For countersunk and button-head variants, chamfer the through-hole to seat the head flush without preloading the head/shank fillet.
When to Step Up or Down from M12
When the joint preload approaches the proof load of M12 class 8.8, step up to M16 class 8.8 (or move to M12 class 10.9). When the joint is over-specified, M10 often saves weight and cost without losing the safety margin.
Custom manufacturing · Made to drawing
Need torx countersunk head screw in a size this table does not list?
This page covers M12 torx countersunk head screw. Thread size and pitch, length, property class, drive form, head geometry and head marking are all specifiable — the standard part is where it starts, not where it stops. Made by cold heading or warm forging.
Minimum order from 2,000 pieces; samples within 7 days of drawing approval.
